Accessories

The SparkFun Qwiic Quad Relay is a unique power accessory board that has been designed for switching not one but four high powered devices from you...

SF-COM-15102

Are you trying to make a quick dime from electronics? Why limit yourself to dimes? This coin acceptor will take three different kinds of coin! Whet...

SF-COM-11719

Overview This accessory pack contains headers and connectors that can be soldered to an A-Star Prime SV or A-Star Prime LV, allowing it to be easi...

PL-3110

INTRODUCTION   An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the proces...

DF-DFR0399

This high quality, low profile, pure copper heatsink is a perfect solution for cooling off small surface-mount components such as stepper motor ...

DF-FIT0506

What is a stepper motor? Stepper motor is a brushless DC electric motor that divides a full rotation into a number of equal steps The motor's po...

DF-DRI0043

he Disposable ECG electrode is used for ECG or other biopotential measurements. It is composed of 12 adhesive electrodes, using nonwoven fabric ...

DF-FIT0510

Need a USB jack for charging or powering a project, but don't want to lug around a computer? This switching supply gives a clean regulated output a...

AF-501

Spring terminal blocks will simplify your wiring and make your project more rugged. Instead of soldering wires to your perf board, solder in these ...

AF-1081

Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll...

AF-1125

We put a PermaProto full sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It ha...

AF-1135

One can never have enough socks, or USB ports. Add some more USB and Ethernet capability to your Raspberry Pi Zero or, really, any kind of tablet o...

AF-2992

We've got a simple and highly functional solution to wiring your Adafruit Feather board! These 0.1" Pitch Terminal Blocks, are exactly the right si...

AF-3173

Metal long standoffs: 1" long x ¼" OD. Used to get your proto board up off the table. #4-40 thread. Fits most development boards with available hol...

SF-PRT-10738

Standard Philips-head 4-40 screws. They are ½" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout b...

SF-PRT-10452

This is a 4.8-46V, 2A Dual Motor Controller which is the revised version of the DF-MDV1.0. Its performance has been improved greatly. It can bear ...

DF-DRI0002

The Sabertooth 2X25 is one of the most versatile, efficient and easy to use dual motor drivers on the market. It is suitable for high powered ro...

DF-DRI0004

It comes with 20 of each value: 1R 1.2R 1.5R 1.8R 2R 2.2R 2.7R 3R 3.3R 3.9R 4.7R 5.1R 6.2R 6.8R 8.2R 10R 12R 15R 18R 20R 22R 27R 30R 33R 39R 47R ...

DF-FIT0119

This is an IC Test Clip for 8-pin small outline integrated circuits (SOIC). This test clip assures a secure connection to all chip leads on an 8-pi...

SF-COM-13153

Connect this to that without soldering using these quick terminal blocks. They allow connecting of two sets of four wires together using just a fla...

AF-677

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of ...

AF-3553

If you love DIY cable-rigging, then these HDMI adapters are right up your alley! Making custom HDMI cables has never been easier. Just grab one of ...

AF-3559

Here's another super handy add-on for your Raspberry Pi computer, perfect for 'head-less' setups! The PiUART adds a MicroUSB to serial connection s...

AF-3589

Put your round robot in the driver seat with the Sphero Chariot.Available in 3 colours, this chariot adds another level of creativity to Sphero. Le...

MG-ACH001BLU

If you already have a 7" TFT that is about 165mm x 105mm in size (with a visible area equal to or smaller than 152mm x 91mm), you can put this glas...

AF-1676

This handy bent-wire display stand was originally designed to hold up 7" tablets but the rubberized design is great for general purpose electronics...

AF-1679

This is the back panel pcb of 1602 Arduino LCD Shield. This shield allows you to place your own LCD onto this shield. It only requieres a 16x2 H...

DF-DFR0009-BP

Here is a simple 5 pack of green LED for LilyPad. Light up the night! LilyPad is a wearable e-textile technology developed by Leah Buechley and ...

DF-DFR0167-G

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields. SPECIFICATIONS Pins are spaced by 0.1"...

DF-FIT0164

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot ...

DF-FIT0182

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot ch...

DF-FIT0183

The serial enabled LCD allows you to control a parallel based LCD over a single-wire serial interface. Included in this product is a white on black...

SF-LCD-09067

This is a 16 character by 2 line display that runs at 3.3V. Utilizes the common ST7066/HD44780 parallel interface (datasheet). Interface code is wi...

SF-LCD-09053

Description: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed below. Sold in single units.

SF-PRT-08995

This handy bent-wire stand was originally designed to hold tablets from 8-10 inches but the rubberized design is great for general purpose electron...

AF-1753