Wearables in Arduino & Microcontrollers

Flat 4xAA battery holder with a 2.1mm barrel jack connecter, suited for projects including the the Arduino development board UNO.

LB-LR0309-16

Bluno Beetle - The smallest Arduino Board is another milestone in wearable electronics device area based arduino uno, which makes DIY users have mo...

DF-DFR0339

NEW VERSION AVAILABLE HERE EagLED is Little Bird Electronics' wearable development kit. It's a complete Arduino compatible microcontroller that has...

LB-EAGLED

The Adafruit Gemma M0 is a super small microcontroller board, with just enough built-in to create many simple projects. It may look small and cute:...

AF-3501

Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull...

SF-DEV-13883

FLORA is Adafruit's fully-featured wearable electronics platform. It's a round, sewable, Arduino-compatible microcontroller designed to empower ama...

AF-659

As of October 9th, 2015 the 5V Trinket comes with a micro-USB connector instead of a mini-USB connector!Trinket may be small, but do not be fooled ...

AF-1501

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure ...

SF-DEV-13903

Love FLORA but want a bite-sized version? Look no further, GEMMA is a tiny wearable platform board with a lot of might in a 1" diameter package. Po...

AF-1222

This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into ...

SF-DEV-14013

We designed this board to give the user a low profile button without any sharp edges. Button closes when you push it and opens when you release (mo...

SF-DEV-08776

We still love the Pro Trinket but the bit-bang USB technique it uses doesn't work as well as it did in 2014. So while we still carry the Pro Trinke...

AF-2000

This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew in...

SF-DEV-14014

This is a simple pack of five Green LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew int...

SF-DEV-14011

We know you love adding color to your e-textiles, adding the LilyPad Pixel Board to your project will only make it better. The pixel board is compa...

SF-DEV-13264

The LilyPad ProtoSnap Plus is a sewable electronics prototyping board that you can use to explore circuits and programming, then break apart to mak...

SF-DEV-14346

Get started with Adafruit GEMMA with this lovely starter kit! Included is everything you need to make a basic project. There's a GEMMA board, four ...

AF-1657

Detecting temperature changes has never been easier. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an...

LB-LS0239

Trinket may be small, but do not be fooled by its size! It's a tiny microcontroller board, built around the Atmel ATtiny85, a little chip with a lo...

AF-1500

We still love the Pro Trinket but the bit-bang USB technique it uses doesn't work as well as it did in 2014. So while we still carry the Pro Trinke...

AF-2010

This is a small board for prototyping through-hole components with the LilyPad system. There are an array of pins all shorted together with 10mil t...

SF-DEV-09102

What do you get when you combine an Adafruit classic with geniuses at Arduino? The Arduino GEMMA! It's a tiny wearable platform board with a lot of...

AF-2470

We're no longer selling this pack of Pro Trinket 3V+5V, we recommend our Metro Mini (5V 328P with USB-Serial Converter), Feather 328P (3.3V 328P wi...

AF-2085