Adafruit - Breakout Boards, Sensors, and Kits

This RF adapter bit is great for anyone doing RF work. Depending on the dev-board and antenna you have, you may be faced with either RP-SMA or SMA ...

AF-919

This here is your standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Teensy, USB Lipo charger (among other things)...

AF-899

This 4"/100mm long swivel dipole antenna has 2dBi of gain and 50Ω impedance so it will work fantastically with just about any 2.4-2.5GHz wireless r...

AF-944

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be jus...

AF-3662

This handy USB extension cable will make it easy for you to enclose a device that has a micro-B type port. We think this would be most handy when p...

AF-937

This handy USB extension cable will make it easy for you to enclose a device that has a mini-B USB type port. We think this would be most handy whe...

AF-936

The INA219 FeatherWing makes power-monitoring problems a thing of the past. Instead of struggling with two multimeters, you can just use the handy ...

AF-3650

This handy USB extension cable will make it easy for you to extend your USB cable when it won't reach. The connectors are gold plated for years of ...

AF-993

This panel mount cable will allow you to enclose a device that has a USB A port, and also converts it to a modern USB C connector at the same time....

AF-4053

This panel mount cable will allow you to enclose a device that has a USB Micro B port, and also converts it to a modern USB C connector at the same...

AF-4056

Design a clock, timer or counter into your next project using our pretty 4-digit seven-segment display. These bright crisp displays are good for ad...

AF-1001

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices l...

AF-1002

If you need to add a panel-mount connection for Ethernet, but don't have the time or ability to cut a custom oval or square hole, this HDMI Round P...

AF-4129

This electret capsule microphone is the same one we use in our great microphone amplifier board. It contains a small vibrating element that will ou...

AF-1064

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface.Th...

AF-1070

Spring terminal blocks will simplify your wiring and make your project more rugged. Instead of soldering wires to your perf board, solder in these ...

AF-1081

This module is the best way to add a GPS to your wearable project. It's part of the Adafruit Flora series of wearable electronics, designed specifi...

AF-1059

Oh say can you seeBy the knob's early light...Sorry - we thought that was clever.  And while it wasn't really, this potentiometer definitely is! We...

AF-4133

This new Adafruit Pi Plate makes it easy to use a blue and white 16x2 Character LCD. We really like the 16x2 Character LCDs we stock in the shop. U...

AF-1115

He told you "Go West, young maker!" - but you don't know which way is West! Ah, if only you had this triple-axis accelerometer/magnetometer compass...

AF-1120

Add a power switch to any project simply by plugging this between the power supply. This is the most useful thing you never knew you needed! You'll...

AF-1125

That new Raspberry Pi® Model A or B computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/out...

AF-862

We put a PermaProto full sized proto board in a blender with a Pi Cobbler and out emerged this very tasty confection - the PermaProto for Pi! It ha...

AF-1135

Add more power to your robot with this metal-geared MG90S servo. The tiny little servo can rotate approximately 90 degrees (45 in each direction), ...

AF-1143