Adafruit - Breakout Boards, Sensors, and Kits

This wire is flexible, strong, and super easy to solder, too! Stranded core wire is best used for wiring jigs where theres bending or movement e...

AF-2979

This wire is flexible, strong, and super easy to solder, too!Stranded core wire is best used for wiring jigs where theres bending or movement expec...

AF-2980

This wire is flexible, strong, and super easy to solder, too!Stranded core wire is best used for wiring jigs where theres bending or movement expec...

AF-2981

A Feather board without ambition is a Feather board without FeatherWings! This is the Non-Latching Mini Relay FeatherWing. It gives you power to co...

AF-2895

This here is your standard A-B USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Arduino, USBtinyISP (among other things). 3 fe...

AF-62

When we were putting together the TV-B-Gone kit, we started imagining a dystopian future, filled with televisions, where this kit would be super us...

AF-73

Adding quality audio to an electronic project is surprisingly difficult. Here is a shield for Arduino 328's that solves this problem. It can play u...

AF-94

This is the Adafruit Feather 32u4 LoRa Radio (RFM9x). We call these RadioFruits, our take on an microcontroller with a "Long Range (LoRa)" packet r...

AF-3079

The Prop Shield with Motion Sensors for Teensy 3.2 and Teensy-LC is meant for making interactive light and sound effects on small handheld props an...

AF-3085

This is our most popular XBee wireless module: the series 1 802.15.4 protocol 1mW with wire antenna. Its good for point-to-point, multipoint and co...

AF-128

The best mini-vise for working on smaller PCBs (2.875" or less in one dimension)! The jaws are strong plastic that wont damage the PCB and doesn't ...

AF-151

This high-torque standard servo can rotate approximately 180 degrees (90 in each direction). You can use any servo code, hardware or library to con...

AF-155

Tiny little servo can rotate approximately 180 degrees (90 in each direction), and works just like the standard kinds you're used to but smaller. Y...

AF-169

This kit is for making your own breadboard-friendly very low dropout adjustable power supply. A good power supply is essential to electronic projec...

AF-184

This is an extra large proto-shield, specifically designed for the Mega! It comes with PCB, two buttons and a full set of stacking headers. You can...

AF-192

The Teensy 2.0 is a complete USB-based microcontoller development system, in a very small footprint! All programming is done via the USB port. No s...

AF-199

6" (150mm) long jumper cable of 6 conductors, 0.1" spacing with two 'female'/sockets on either end. Great for wiring up ShiftBrites together!

AF-206

This little sensor is a great way to add UV light sensing to any microcontroller project. The VEML6070 from Vishay has a true UV A light sensor and...

AF-2899

Looking for an ultra-thin heat sink for your Raspberry Pi 3? Check out this nice and slim 13x13x3mm Heat Sink!This heat sink is made from high qual...

AF-3084

We are very excited to have one of the first (and we think the best) Enclosure for Arduino & project box! Here are all the details: Dimen...

AF-271

The world's first and only open-source hardware charger: The MintyBoost®!New version! Works with the new iPhone 4 & 5 and more! Please review t...

AF-14

One can never have enough socks, or USB ports. Add some more USB and WifI capability to your Raspberry Pi or, really, any kind of computer with thi...

AF-2937

These LED strips are fun and glowy. There are 30 RGB LEDs per meter, and you can control the entire strip at once with any microcontroller and thre...

AF-285

Snap the Pimoroni Unicorn pHAT on top of a Raspberry Pi Zero (or really, any Raspberry Pi with a 2x20 connector) for a fun 4x8 RGB LED matrix power...

AF-3181