Adafruit Australia

This little sensor looks an awful lot like the popular DHT11/DHT22 temperature and humidity sensors, but unlike classic DHT sensors, it has an I2C ...

AF-3721

We're doffing our Mini Black HAT Hack3r for the evening because it's showtime for Pimoroni's pHAT Stack! This expansive breakout PCB offers 6 sets ...

AF-3742

Totaling 420 pieces, this White Nylon M2.5 Screw Set is a must-have smörgåsbord for your workstation. You'll have more than enough screws, nuts, an...

AF-3658

This RF adapter bit is great for anyone doing RF work. If your receiver/transmitter/transceiver has an MCX connector but you really want to tie it ...

AF-1531

This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP...

AF-1381

OK, this item is pretty simple - it's a panel mount pushbutton. It's not that exciting, no LEDs, no bells & whistles. But we really like it any...

AF-1504

This is a special-purpose charger just for the rechargeable LIR2450 Lithium Ion coin cells. Slide the coin cell in the right way, and plug into any...

AF-1573

NooBs 2.8 is the fastest way to have a variety of operating systems on your Pi. Available on a 16G card, you can now boot multiple OS's such as Ras...

AF-1583

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake ...

AF-1608

FPC cables are super thin and flexible. They're often used in electronics when a a round cable would be too bulky, especially if you're dealing wit...

AF-1682

A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It is able to deliver 2 x 2.8...

AF-1712

Silicone-sheathing wire is super-flexible and soft, and its also strong! Able to handle up to 200°C and up to 600V, it will do when PVC covered wir...

AF-2006

The Qualia Retina driver board is a work of art (it was designed by resident engineer KTOWN). It's used in the Adafruit Qualia 9.7" DisplayPort Mon...

AF-1716

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show...

AF-1755

Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show...

AF-1756

This 5050 LED breakout PCB set will make your life much much easier and get you prototyping faster than ever. Solder your 5050 sized LED to either ...

AF-1762

Remember when you were a kid and there was a birthday party at the pool and your parents totally embarrassed you by slathering you all over with su...

AF-1777

Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference. We have a couple digital thermocouple amplifiers i...

AF-1778

This 1K potentiometer is a two-in-one, good in a breadboard or with a panel. Its a fairly standard linear taper 1K ohm potentiometer, with a grippy...

AF-1789

Push once to turn on, push again to turn off! This clicky switch makes a great power switch or mode toggler. We like this switch because it's bread...

AF-1683

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for eas...

AF-1867

This slim and modern potentiometer is small and compact, yet looks good and has a nice feel. We hand selected the best knobs for your project in di...

AF-2057

This is really the fanciest, best feeling knob we've ever seen. Using this knob sort of reminded us of driving along the Amalfi coast in a perfectl...

AF-2056