Adafruit Australia

Listen up! This single  2.8" x 1.2" speaker is the perfect addition to any audio project where you need 4 ohm impedance and 3W or less of power. We...

AF-4445

We're with the squad back at New York's hottest cyberpunk club, Near Field Commune(ication), and it's still got everything, Adabot & the Circui...

AF-4387

The SparkFun Qwiic Adapter can make any old I2C board or sensor a STEMMA QT / Qwiic-enabled one. This adapter breaks out the I2C pins from the JST ...

AF-4527

As technology changes and adapts, so does Adafruit. This  USB Type A to Type C cable will help you with the transition to USB C, even if you're sti...

AF-4473

Looking for another way to keep your project cool? Hook up this 5V Mini Cooling Fan and prevent from overheating! Of course, it's also great for us...

AF-4468

For the easiest way possible to measure twists, turn to this STEMMA potentiometer breakout (ha!). This plug-n-play pot comes with a JST-PH 2mm conn...

AF-4493

Do you feel like you just don't have a CLUE? Well, we can help with that - get a CLUE here at Adafruit by picking up this sensor-packed development...

AF-4500

Only 13mm long, Fomu really puts the micro in microprocessor. Fomu is a fully open-source, programmable FPGA device that sits inside a USB Type-A p...

AF-4332

SPRESENSE is a low-power board computer for the IoT that is equipped with a GPS receiver and supports High-Resolution Audio codecs. The board allow...

AF-4419

Spresense is a compact development board based on Sony’s power-efficient multicore microcontroller CXD5602. It allows developers to create IoT appl...

AF-4418

The latest addition to Spresense's hardware ecosystem is the Spresense Camera Board that connects directly to the main board’s camera interface. Th...

AF-4417

As technology changes and adapts, so does Adafruit, and speaking of adapting, this right angle adapter is USB C socket-to-plug.USB C is the latest ...

AF-4432

This is a blank 13.56MHz RFID/NFC Laundry Tag Button with an NTAG213 chip - often used for laundry or garment identification, information sharing, ...

AF-4429

The first step in a robotics project is to get a motor spinning. Once you've done that you quickly learn that not all motors go the same speed, eve...

AF-4416

These iridescent silver-bluish-purple sequins can be used for a variety of maker projects for some shimmery wintery glitz. Also perfect as snowflak...

AF-4439

This LED Ring Light is designed for use with microscopes but we kinda like the design and think it could be a really nice LED element for costuming...

AF-4433

Looking for a way to keep your Raspberry Pi 4 running cool and also look cool? We've got a two-birds-one-stone solution for you. This enclosure kit...

AF-4340

STEMMA plug-and-play parts make your next project soldering-free! This is the STEMMA Non-Latching Mini Relay. It gives you power to control, and co...

AF-4409

Always be ready rock out or record with this 5-watt Guitar Amplifier, Portable Recorder, and USB Audio Interface from Monoprice.This handheld 5-wat...

AF-4402

ST takes flight in this upcoming Feather board. The new STM32F405 Feather (video) that we designed runs CircuitPython at a blistering 168MHz – our ...

AF-4382

EVA foam is one of the best and easiest go-to materials for constructing costumes and props. It's light, inexpensive, versatile, and can easily be ...

AF-4349

The smallest, most feature-rich ESP32 dev board is here! TinyPICO has incredible processing power for a board that's shorter than an alkaline batte...

AF-4335

The TLV493D 3-axis magnetometer is a great little sensor for detecting magnets in 3D. In fact, the manufacturer Infineon suggests it could be used ...

AF-4366

The Grove Shield FeatherWing for Particle Mesh and all Feathers is an add-under for any Particle Mesh or Feather board, so that you can easily inte...

AF-4357