Products

The light sensor, also known as the light dependent resistor (LDR). Typically, the resistance of the light sensor will decrease when the am...

TB-XC4574

This is a magnetic switch module with Linker kit standard connection. It is based on encapsulated dry reed switch of single-pole, single th...

TB-XC4581

A standard 12mm square momentary button mounted for the Linker connection. The button is big and has a solid tactile click for assurance. Can be ...

TB-XC4571

This sensor module uses a reflective infrared sensor. The infrared light is emitted and reflected back to the receiver, it's then inverted ...

TB-XC4590

The Linker Rotary Potentiometer Module produces analog output between 0 and Vcc (5V DC with Arduino) on its D1 connector. The D2 connector ...

TB-XC4578

The Linker RTC module is based on the clock chip DS1307, which supports the I2C protocol. It utilises a Lithium cell battery (CR1225). The ...

TB-XC4584

Serial Servo Driver is a servo driver board that can drive up to 8 servos with a precision of 5us. The communication interface is TTL UART ...

TB-XC4586

The slide potentiometer is a linear variable resistor with a total resistance of 10k. When you move the lever from one side to the other, i...

TB-XC4579

The Sound sensor module is a simple microphone. Based on the power amplifier LM386 and the electret microphone, it can be used to detect th...

TB-XC4582

The Linker Temperature Module uses a Thermistor to detect the ambient temperature. The resistance of a thermistor will increase when the am...

TB-XC4576

The Linker Tilt Module is the equivalent of a button, and is used as a digital input. Inside the tilt switch is a pair of balls that make c...

TB-XC4575

A capacitive touch sensor to replace a push button. Low in power consumption, fast response and easy to operate. Voltage reads 0V when idle...

TB-XC4572

This vibration sensor module of Linker Kit uses a spring based sensor. When there is vibration, it will output a digital signal. The SW-180...

TB-XC4587

LinkIt Assist 2502, a co-design product by Seeed Studio and MediaTek , is development board for prototyping Wearables and Internet of Things(IoT)...

SS-102990179

The LinkIt™ Connect 7681 development board provides you with easy access to the five GPIO pins and one UART port — each with an LED — of the Medi...

SS-113990100

The LinkIt™ Connect  7681 module  is a low-cost, low-power consumption component for IoT devices. The module integrates the MediaTek MT7681, whi...

SS-317060009

      main feature All-in-one features Includes ARM7 EJ-S™, GSM, GPRS, Wi-Fi, Bluetooth BR/EDR/BLE, GPS, Audio codec, and SD c...

SS-102030002

LinkM is a USB adapter that addresses two of the most frequently-requested BlinkM features. It enables you to program BlinkMs without setting up a ...

SF-COM-09903

Every super spy has a small compact camera at their disposal just to get the advantage on the bad guy and though you may not be a “00” this high re...

SF-SEN-12804

Are you a super spy trying to spot ninja assassins in the dark? Or maybe you’re just trying to figure out who’s been sneaking to the kitchen at nig...

SF-SEN-11610

You hacked, modded or made something with Linux! Adafruit offers a fun and exciting "badges" of achievement for electronics, science and engineerin...

AF-553

You hacked, modded or made something with Linux! Adafruit offers a fun and exciting stickers to achievement for electronics, science and engineerin...

AF-663

This Charger - MicroUSB is designed for single-cell 3.7V lithium battery. With its tiny body, you can easily integrate it into your applications. T...

DF-DFR0667