Prototyping in Arduino & Microcontrollers

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm(0.22x0.08"), c...

DF-FIT0151

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new stan...

AF-2821

3.7V Polymer Lithium Ion Battery - 1000mAh Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The outp...

DF-FIT0120

These two Short Male Headers alone are, well, lonely. But pair them with any of our Feather boards and you're in business!These headers are particu...

AF-3002

This is a cute half size breadboard, good for small projects. It's 2.2" x 3.4" (5.5 cm x 8.5 cm) with a standard double-strip in the middle and two...

AF-64

A Feather board without ambition is a Feather board without FeatherWings!This is the FeatherWing Proto - a prototyping add-on for all Feather board...

AF-2884

This adapter allows you to connect a barrel jack connector to bare wires. One end has screw terminals and the other has a 5.5x2.1mm, center-positi...

DF-FIT0110

This Solar lipo charger is designed for single Lithium battery (3.7V) for intelligent charging, with input reverse polarity protection. The maxim...

DF-DFR0264

INTRODUCTION Simple 4 Cell AA Battery holder with 5" tinned leads, square configuration. This holder features a slidin...

DF-FIT0080

This battery holder can hold 3 AA batteries which provides 3.6V rechargeable battery pack with NiMH / NiCd cells or 4.5V battery pack with Alkal...

DF-FIT0362

The SparkFun OpenLog is an open source data logger that works over a simple serial connection and supports microSD cards up to 64GB. The OpenLog ca...

SF-DEV-13712

“How could something so simple be so useful?”  We heard once that in the 4th millenium B.C. some guy asked the person who invented the wheel tha...

AF-85

Need a clean energy source for your project? Check out this compact,high quality,high output endurable solar panel.The peak power output is around...

DF-FIT0330

This is the FeatherWing Tripler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are t...

AF-3417

This is the FeatherWing Doubler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are t...

AF-2890

Ethernet Shields generally come with stackable headers fitted, but the big problem is that because the RJ45 jack is so high it's not possible to st...

FT-PSS

Breadboards are great for quickly prototyping Arduino projects on the workbench, but they're really inconvenient if you want to make something a bi...

FT-PSB

This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with off...

SF-DEV-13746

This prototyping shield is the best out there (well, we think so, at least), and now is even better with Version R3 - updated for the most compatib...

AF-2077

Classic 9V connector terminated with 2-pin polarized Molex connector. 15cm in length. To supply the power to Arduino, we recommend the DC Power Ja...

DF-FIT0111

This is a 8-pin female header, with extra long legs – great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

SF-PRT-09279

This is a cute half-size breadboard with an assortment of small jumper wires, great for prototyping. Breadboard is 2.2" x 3.4" (5.5 cm x 8.5 cm) wi...

AF-3314

The LilyPad ProtoSnap Plus is a sewable electronics prototyping board that you can use to explore circuits and programming, then break apart to mak...

SF-DEV-14346

This battery holder can hold 6 AA battery which can make 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from alkaline c...

DF-FIT0266

This is the very first prototyping shield for Arduino in the market since 2010. It comes with prototyping area that you can sold led , switch o...

DF-DFR0019

The Arduino Prototyping Shield makes it easy for you to design custom circuits for the MEGA standard Arduino pinout The Arduino Prototyping Shield ...

PI-A000080

The Terminal Block Breakout FeatherWing kit is like the Golden Eagle of prototyping FeatherWings (eg. majestic, powerful, good-looking). To start, ...

AF-2926

A super-size prototyping shield to fit the EtherMega, EtherDue, and other Arduino compatible "Mega" size boards so you can fit your own parts for p...

FT-PSM

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The Lithium Battery Charger can charge 3.7V LiPo ba...

DF-DFR0208

This battery holder can hold 6 AA battery which is able to become a 7.2 V rechargeable battery pack from NiMH / NiCd cells or 9V battery pack from ...

DF-FIT0141

This simple cable has so many uses! Plug a 9V battery into one end and connect the other end to anything with a 5.5x2.1mm, center-positive barre...

DF-FIT0131

Simple 4 Cell AA Battery holder with 5" tinned leads, square configuration. SPECIFICATIONS Battery Quantity: 4 Battery typ...

DF-FIT0079

This small capsule is a 4.5V button cell battery holder for mini power solutions.Its minimalism design in clean white cylinder body and matte surf...

DF-FIT0337

This is a 6-pin female header, with extra long legs – great for stacking Arduino shields. Pins are spaced by 0.1". Documents: Datasheet

SF-PRT-09280

This is a design for an open-source prototyping shield for Arduino Mega. It has tons of cool features, to make prototyping on your Arduino easy....

DF-DFR0016

The next generation Proto-ScrewShield is a dual-purpose prototyping shield. Not only does it have a large 0.1" grid prototyping area but it also ex...

AF-196