Arduino & Microcontrollers

A capacitive touch sensor to replace a push button. Low in power consumption, fast response and easy to operate. Voltage reads 0V when idle...

TB-XC4572

Two momentary push buttons mounted on a single board for Arduino/pcDuino via the Linker connection. Can be used as a pair of reset and swit...

TB-XC4573

The Linker Temperature Module uses a Thermistor to detect the ambient temperature. The resistance of a thermistor will increase when the am...

TB-XC4576

This hall module hosts an magnetic hall sensor that senses the presence of magnetic field. If there is an magnetic field present, it will r...

TB-XC4577

The Linker Rotary Potentiometer Module produces analog output between 0 and Vcc (5V DC with Arduino) on its D1 connector. The D2 connector ...

TB-XC4578

The slide potentiometer is a linear variable resistor with a total resistance of 10k. When you move the lever from one side to the other, i...

TB-XC4579

This buzzer module will generate around the audible 2kHz range. Linksprite Page   Specifications ...

TB-XC4580

The Sound sensor module is a simple microphone. Based on the power amplifier LM386 and the electret microphone, it can be used to detect th...

TB-XC4582

The Linker Infrared Receiver Module is used to receive infrared signals and also used for remote control detection. There is an IR detector...

TB-XC4583

The Linker RTC module is based on the clock chip DS1307, which supports the I2C protocol. It utilises a Lithium cell battery (CR1225). The ...

TB-XC4584

This vibration sensor module of Linker Kit uses a spring based sensor. When there is vibration, it will output a digital signal. The SW-180...

TB-XC4587

Flame sensor module of Linker kit is only sensitive to the light in the frequency band of infrared and ultrviolet. This breakout board ...

TB-XC4588

This sensor module uses a reflective infrared sensor. The infrared light is emitted and reflected back to the receiver, it's then inverted ...

TB-XC4590

This sensor pack for Arduino includes the following components: 1 x IR Receiver Sensor 1 x Tilt Sensor 1 x Photo Cell Sens...

TB-XC4593

This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work with 5V Ardui...

TB-XC4594

This is a breakout board for the Silicon Laboratories Si4703 FM tuner chip. Beyond being a simple FM radio, the Si4703 is also capable of d...

TB-XC4595

Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card,...

TB-XC4597

GPS Bee, a SKM58 breakout that adds a Xbee compatible footprint for SKM58. The SKM58 Series with embedded GPS antenna enables high perf...

TB-XC4600

The serial UART 16x2 LCD allows you to control a parallel based LCD over a single-wire serial interface. The serial LCD takes care of all t...

TB-XC4601

Receiving power from a USB socket or DC socket, this module adds a compact power supply to your breadboard. Features: * Plugs strai...

TB-XC4606

A compact LED Matrix display featuring 256 individually addressable LED’s. Stack multiple boards side by side for a larger display. Fea...

TB-XC4607

The Arduino compatible boost module can be used to provide higher voltages for your project, such as running 5V Arduino projects from Lithi...

TB-XC4609

Large 32 x 16 pixel white LED display for your Arduino to create message boards, clocks, spectrum analysers, games for the home, office, sh...

TB-XC4622

Large 32 x 16 pixel blue LED display for your Arduino to create message boards, clocks, spectrum analysers, games for the home, office, sho...

TB-XC4623