Battery Holders

This 5m length of EL wire (electroluminescent wire) is a flexible wire coated with phosphor which glows blue when applied with the appropriate volt...

LB-LR0335-PI

Flat 4xAA battery holder with a 2.1mm barrel jack connecter, suited for projects including the the Arduino development board UNO.

LB-LR0309-16

The EagLED Battery Holder for CR2032 is a coin cell battery holder that holds in place a CR2032 button battery using a screw. Equipped with an ON/...

LB-EAGLED-BATTERY

Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull...

SF-DEV-13883

This is a simple coin cell battery holder that can enclose two CR2032 batteries inside itself, and safely kept closed via two phillips head screws....

LB-PRT-12618

These are a simple 9v battery holder with DC connector.

LB-LR0295

This is an incredibly simple one cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fa...

LB-LR0309-18

This 5m length of EL wire (electroluminescent wire) is a flexible wire coated with phosphor which glows blue when applied with the appropriate volt...

LB-LR0335-V

NEW VERSION with SCREW close   This E-Textiles Coin Cell Battery Holder has a small slide switch installed on the board, in-line with the power so ...

LB-BATTERYSNAP

This 5m length of EL wire (electroluminescent wire) is a flexible wire coated with phosphor which glows blue when applied with the appropriate volt...

LB-LR0335-W

This 5m length of EL wire (electroluminescent wire) is a flexible wire coated with phosphor which glows blue when applied with the appropriate volt...

LB-LR0335-B

DescriptionThis battery enclosure (with switch) for the BBC micro:bit is the perfect way to power your micro:bit on the go.Specifications:  2x AA B...

LB-BATTERYAA

This battery holder can hold 3 AA batteries which provides 3.6V rechargeable battery pack with NiMH / NiCd cells or 4.5V battery pack with Alkal...

DF-FIT0362

INTRODUCTION Simple 4 Cell AA Battery holder with 5" tinned leads, square configuration. This holder features a slidin...

DF-FIT0080

This is a unique two-cell AAA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been terminated with a JST-PH conn...

SF-PRT-15101

Single Slots 1x 9V Battery Holder Case with wire leads for soldering / connecting.Keep your batteries organised and protectedLead Cable Length:Appr...

LB-LR0309-20

This battery holder features two 6″, 24-gauge leads that have 5 mm of insulation stripped off of the ends.

PL-1152

This battery holder connects 3 AAA batteries together in series for powering all kinds of projects. We spec'd these out because the box is slim, an...

AF-727

This is a small solid crystal acrylic case. You can place your micro:bit into it. It can wrap up the whole body of micro:bit board except the two b...

EF-EF10111

This 5m length of EL wire (electroluminescent wire) is a flexible wire coated with phosphor which glows blue when applied with the appropriate volt...

LB-LR0335-LB

This battery holder is used to hold 3 zinc-manganese batteries (non-rechargeable) or 3 NiMH / NiCd batteries, which can change into a 4.5V battery ...

DF-FIT0610

  This is a simple 6 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector.

LB-LR0294