Breakout Boards

Low-cost basic SOIC break out boards. These are custom PCB boards that interface standard SOIC devices to standard .1" headers.Pad layout fits all ...

SF-BOB-00496

Because the Arduino (and Basic Stamp) are 5V devices, and most modern sensors, displays, flash cards and modes are 3.3V-only, many makers find that...

AF-395

Yaaar! Become your very own pirate radio station with this FM radio transmitter. This breakout board, based on the best-of-class Si4713, is an all-...

AF-1958

Since we first started carrying NeoPixels back in 2012, the chainable RGB LEDs have taken over the world. And a big part of that success is due to ...

AF-3975

This driver board gives your micro:bit the ability to drive two channel DC motors and three channel servos. It's an ideal choice for you to DIY mob...

SS-105990091

These Simple RF receivers are the easiest way possible to add wireless control, painlessly! There's no programming, configuring or addressing - sim...

AF-1097

This versatile piezo-element module can be used for both input or output! It can be used as a noise-maker driven by your microcontroller for audibl...

FT-SOUND

Combining an accelerometer, a magnetometer, and a gyroscope all in one tiny package with an Arduino-friendly I2C interface. Perfect for building a...

FT-IMU9

 Sense magnetic presence, rotating wheels and magnets, door and arm sensors, and anything else magnetic nearby this sensor.Click here for our Hall ...

FT-HALL

Beguiled by a fancy new chip that is only available in a SOIC or MSOP/(T)SSOP pinout? This breakout PCB set will make your life much much easier an...

AF-1212

Add motion and direction sensing to your wearable FLORA project with this high precision 3-axis Accelerometer+Compass sensor. Inside are two sensor...

AF-1247

The NXP Precision 9DoF breakout combines two of the best motion sensors we've tested here at Adafruit: The FXOS8700 3-Axis accelerometer and magnet...

AF-3463

This new version adds 2 standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer...

SF-SEN-09836

This is the newest revision and fixes issues with the last board. This breakout board pairs an SP3485 RS-485 transceiver with an FT232RL USB UART I...

SF-BOB-09822

The SparkFun XA1110 GPS Breakout is a small I2C-supported module built for easy hookup, thanks to our Qwiic Connect System. Equipped with the ...

SF-GPS-14414

The SparkFun H3LIS331DL Triple Axis Accelerometer Breakout is a low-power, high-g accelerometer with I2C and SPI interface options. Though not...

SF-SEN-14480

This is a breakout board for the ISD1932, a multiple-message record/playback device. This single chip can record up to 64 seconds worth of voice me...

SF-BOB-10653

This is a simple breakout board for Analog Device’s AD5330 8-bit digital-to-analog converter (DAC). The AD5330 has a parallel interface, and can op...

SF-BOB-09719

A mini class D with AGC and I2C control? Yes please! This incredibly small stereo amplifier is surprisingly powerful. It is able to deliver 2 x 2.8...

AF-1712

This 5050 LED breakout PCB set will make your life much much easier and get you prototyping faster than ever. Solder your 5050 sized LED to either ...

AF-1762

Simple but effective - this breakout board has a CR1220 coin cell battery holder soldered on, an on/off switch and 0.1" pitch breakout pins for eas...

AF-1867

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontroller...

AF-2210

Would you like to add audio/sound effects to your next project, without an Arduino+Shield? Or maybe you don't even know how to use microcontroller...

AF-2220

This touch-able add on HAT for Raspberry Pi will inspire your next interactive project with 12 capacitive touch sensors. Capacitive touch sensing w...

AF-2340