Breakouts, Boards & Electronics

The Arduino TIAN is based on the Atheros AR9342 connected to an Atmel Cortex M0+ 32-bit microcontroller plus all connectivity: Ethernet, Wi-Fi, ...

DF-DFR0401

This is a breakout board for the RN-131g WiFly GSX module, an ultra-low power 802.11b/g transceiver. This board breaks out all pins of the RN-13...

DF-TEL0011

INTRODUCTION The RLY-8 is a network relay controller with open source communication protocol. It integrates 8 channel re...

DF-DFR0290

DFRobot WiFi Shield for Arduino, is part of our wireless family product. This WIFI Shield V3 supports AP + STA dual mode, and is extremely easy ...

DF-TEL0079

DFRobot WiFi Shield, is part of our wireless family product. This WIFI Shield V3 supports AP + STA dual mode, and is extremely easy to connect t...

DF-TEL0078

The Arduino Yun is a newcomer microcontroller board in the Arduino boards family. It is a microcontroller board based on the ATmega32u4 (datashe...

DF-DFR0297

Your power supply problems just got SUPER SOLVED! This 3.3V Buck Converter Breakout board is great for supplying power to low voltage circuits from...

AF-2745

You will roll lucky 7's and connect to nearly any kind of FPC/flex cable with Ladyada's Super Lucky 40-pin FPC to breadboard adapter plate. You get...

AF-1436

Connect to 0.5mm, 1.0mm and even some 2.0mm pitch connectors that you may run across with an FPC stick. We designed this for use in house, to quick...

AF-1325

The bladeRF 2.0 micro xA4 is the next generation Software Defined Radio (SDR) that has been packed into a small form factor and was designed for hi...

SF-WRL-15043

The RoboClaws from Basicmicro (formerly Ion Motion Control) are a family of efficient, versatile, synchronous regenerative motor controllers. They ...

PL-3581

This product is a carrier board or breakout board for Toshiba’s TB67S2x9FTG family of stepper motor drivers; we therefore recommend careful reading...

PL-3098

This product is a carrier board or breakout board for Toshiba’s TB67S2x9FTG family of stepper motor drivers; we therefore recommend careful reading...

PL-3096

Haptic feedback can add a more professional level of interaction to your project. The same satisfying vibration you get when you receive a text mes...

SF-ROB-15181

Beam is a beginner-friendly PCB with 120 LEDs arranged in a 5x24 grid, a great size to display text or animations in your project. Plug in one to f...

AF-3668

Does your project require high-precision, cutting-edge distance measurement? Or maybe speed-, motion-, or gesture-sensing? We’re not talking about ...

SF-SPX-14811

This adorable little board will come in very handy whenever you need a small amount of 5V power. It's the size of a linear regulator, but it's actu...

AF-3661

The Spectacle Inertia Board makes it easy to sense motion or orientation with a Spectacle project. The Spectacle Inertia Board is designed to allow...

SF-DEV-13992

The Accelerometer sensor is an add-on for your RedBot that provides bump and motion detection. The sensor works by measuring acceleration forces on...

SF-SEN-12589

We’ve been using and selling Analog Devices' ADXL accelerometers for a good while now, and now we’ve found another great part in the series! The AD...

SF-SEN-11446

This is a breakout board for the ultra low-power LIS331HH three axis linear accelerometer. The device has a digital I2C/SPI serial interface which ...

SF-SEN-10345

Breakout board for the 3 axis ADXL335 from Analog Devices. This is the latest in a long, proven line of analog sensors - the holy grail of accelero...

SF-SEN-09269

LoRa stands for ‘Long-Range,’ referring to a modulation technique whose specialty is low power transmission of small data packets – perfect for Int...

SF-SPX-14984