DFRobot Australia

A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol ...

DF-SEN0064

With the blooming development of IoT (Internet of Things), more and more people are dedicated to pursue their own IoT dreams. However traditional ...

DF-TEL0113

This high discharge LiPo is a great way to power any R/C, robotic, or portable project. This is an excellent choice for anything that requires a s...

DF-FIT0137

City night is always beautiful. She is just like a charming girl, showing her beauty every time. The colorful light is jewelry, dotted on her dress...

DF-DFR0471

This is the back panel pcb of 1602 Arduino LCD Shield. This shield allows you to place your own LCD onto this shield. It only requieres a 16x2 H...

DF-DFR0009-BP

The ZM 0.3 Megapixel serial JPEG still camera module has a compact size, low power consumption, and stable operation. 5.0V DC Supply. UART: Up t...

DF-SEN0099

This is an Arduino RGB Color Sensor breakout uses TAOS TCS3200 RGB sensor chip and 4 white LEDs. The TCS3200 arduino color sensor can detect an...

DF-SEN0101

Here is a simple 5 pack of green LED for LilyPad. Light up the night! LilyPad is a wearable e-textile technology developed by Leah Buechley and ...

DF-DFR0167-G

This is a 6-pin female header, with extra long legs -- great for stacking Arduino shields. SPECIFICATIONS Pins are spaced by 0.1"...

DF-FIT0164

This is a new version of the FTDI breakout board features an Atmega8U2 programmed as a USB-to-serial converter, the same chip found on the Ardui...

DF-DFR0164

This is a cool touch sensor from DFRobot. You can hook it up to the IO Expansion shield (for arduino) directly. It includes a metallic tape with...

DF-SEN0104

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot ...

DF-FIT0182

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot ch...

DF-FIT0183

Electroluminecent wire, otherwise known as EL Wire, is a thin phosphor coated wire in a tube that lights up when you apply a high AC voltage to it...

DF-DFR0185-LB

Electroluminecent wire, otherwise known as EL Wire, is a thin phosphor coated wire in a tube that lights up when you apply a high AC voltage to ...

DF-DFR0185-HP

Suitable for all kinds of circuit boards, sensors, mechanical support of the installation. They are great for building a multi-level robot ch...

DF-FIT0194

These are typical rubber wheels for small robot mobile platforms. The tire is soft black rubber with light tread for added traction in rugged te...

DF-FIT0199-B

This is a very basic double sided prototyping board with standard 0.1" spacing through holes and four 3mm diameter mounting holes. There are 22...

DF-FIT0203

This is a DFRobot electronic project notebook. We have been using this for a long time and now it has become a necessity for all DFRobot enginee...

DF-DWG0001-B

Have you ever been to a maker faire? You cann't imagine people there are crazy about stickers and stamps.They collected as many different sticke...

DF-DWG0002

This is a 4 pin female-female cable with buckle which we have wired for use with the DFRobot interface shield and other DFRobot products like the ...

DF-FIT0081

This is a 2-pin female housing pin with a pitch of 2.54mm(0.1"). You can make customized cables that mate with the 0.1"-spaced pins. NOTE: D...

DF-FIT0207

INTRODUCTION This is an Arduino Propane Gas Sensor. It uses MQ6 probe to detect iso-butane, propane and liquefied petro...

DF-SEN0131

This non-contact liquid level switch can be triggered when the liquid level fall below the sensor attached to the outside surface of a non-metal...

DF-FIT0212

This is a 12" ribbon cable made of ten jumper wires with different colors. The wires can easliy be pulled apart for individual use and each wire...

DF-FIT0215

An Ultrasonic sensor with scan capability is a must have feature for most robot application. This Ultrasonic scanner kit provides a cost effect...

DF-KIT0020

This is a tube of solder leaded with 2% silver, it is about 3m when stretch to straight line. You can hold the tube while soldering, this makes ...

DF-FIT0230

Flymaple is a Quadcopter controller board, based on the Maple Project. The FlyMaple embeds a STM32F103RET6 (ARM Cortex-M3) as it's main MCU. It ...

DF-DFR0188

Variable resistors also named as potentiometer are electrical equipments having two terminal points in opposite direction. The terminals are use...

DF-FIT0189

The USB 2.0 to RS422/RS485 Cable provides a simple and easy to connect between the USB and RS422/RS485 ports interface. Ideally for PC, thin cli...

DF-FIT0272

INTRODUCTION This is one of our favourite DFRobot customized high quality DC motor. It is a low noise motor and high tor...

DF-FIT0277

Shape Memory metals were developed by NASA for the space industry, and have been used for increasing applications down on earth.For example,ther...

DF-FIT0285

INTRODUCTION Shape Memory metals that were developed by NASA for the space industry, and have been used for increasing...

DF-FIT0261

This is a 6 Dof IMU shield for Arduino, using the ADXL345 accelerometer and the ITG-3200 gyro.This IMU Combo shield also embeded a xbee sockets....

DF-DFR0209

This is an 20 tooth timing pulley with a center diameter of 8mm (0.31"). These pullies are great for many mechanical projects. They are also ver...

DF-FIT0234

This is a SOP16/SOP28/SSOP28 to DIP16/DIP28 Adapter Board.You can change the SOP16/SOP28/SSOP28 to DIP16/DIP28 packaging.So that You needn't to ...

DF-FIT0291

This is a SOP8 to DIP8 Adapter Board. You can change the SOP8 to DIP8 packaging.So that You needn't to buy the DIP chips for prototyping special...

DF-FIT0290

This is 1 meter of PFA tubing with a 6mm diameter. PFA has a high temperature resistance with a melting point of 305C. This tubing is used as a ...

DF-FIT0243

Featured in Make: The Maker's Guide to Boards, DFRobot Leonardo with Xbee Socket is an Arduino Leonardo variant processor.The Arduino Leonardo i...

DF-DFR0221

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS Screw...

DF-FIT0270

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS   ...

DF-FIT0269

This LilyPad Power Supply is Discontinued Now, We recommend other best selling Power Modules as a suitable replacement. A small, but mighty po...

DF-DFR0079

This motor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Pololu wheel 42x19mm and 32x7mm. The brass faceplate has...

DF-FIT0302

A multi-use wrench used for installing the screws nut of the mobile platforms or the 3D printers and other tasks is the cross wrench.Much like a...

DF-FIT0306