DFRobot Australia

This is a 2-pin female housing pin with a pitch of 2.54mm(0.1"). You can make customized cables that mate with the 0.1"-spaced pins. NOTE: D...

DF-FIT0207

INTRODUCTION This is an Arduino Propane Gas Sensor. It uses MQ6 probe to detect iso-butane, propane and liquefied petro...

DF-SEN0131

This non-contact liquid level switch can be triggered when the liquid level fall below the sensor attached to the outside surface of a non-metal...

DF-FIT0212

This is a 12" ribbon cable made of ten jumper wires with different colors. The wires can easliy be pulled apart for individual use and each wire...

DF-FIT0215

An Ultrasonic sensor with scan capability is a must have feature for most robot application. This Ultrasonic scanner kit provides a cost effect...

DF-KIT0020

This is a tube of solder leaded with 2% silver, it is about 3m when stretch to straight line. You can hold the tube while soldering, this makes ...

DF-FIT0230

Flymaple is a Quadcopter controller board, based on the Maple Project. The FlyMaple embeds a STM32F103RET6 (ARM Cortex-M3) as it's main MCU. It ...

DF-DFR0188

Variable resistors also named as potentiometer are electrical equipments having two terminal points in opposite direction. The terminals are use...

DF-FIT0189

The USB 2.0 to RS422/RS485 Cable provides a simple and easy to connect between the USB and RS422/RS485 ports interface. Ideally for PC, thin cli...

DF-FIT0272

INTRODUCTION This is one of our favourite DFRobot customized high quality DC motor. It is a low noise motor and high tor...

DF-FIT0277

Shape Memory metals were developed by NASA for the space industry, and have been used for increasing applications down on earth.For example,ther...

DF-FIT0285

INTRODUCTION Shape Memory metals that were developed by NASA for the space industry, and have been used for increasing...

DF-FIT0261

This is a 6 Dof IMU shield for Arduino, using the ADXL345 accelerometer and the ITG-3200 gyro.This IMU Combo shield also embeded a xbee sockets....

DF-DFR0209

This is an 20 tooth timing pulley with a center diameter of 8mm (0.31"). These pullies are great for many mechanical projects. They are also ver...

DF-FIT0234

This is a SOP16/SOP28/SSOP28 to DIP16/DIP28 Adapter Board.You can change the SOP16/SOP28/SSOP28 to DIP16/DIP28 packaging.So that You needn't to ...

DF-FIT0291

This is a SOP8 to DIP8 Adapter Board. You can change the SOP8 to DIP8 packaging.So that You needn't to buy the DIP chips for prototyping special...

DF-FIT0290

This is 1 meter of PFA tubing with a 6mm diameter. PFA has a high temperature resistance with a melting point of 305C. This tubing is used as a ...

DF-FIT0243

Featured in Make: The Maker's Guide to Boards, DFRobot Leonardo with Xbee Socket is an Arduino Leonardo variant processor.The Arduino Leonardo i...

DF-DFR0221

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS Screw...

DF-FIT0270

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS   ...

DF-FIT0269

This LilyPad Power Supply is Discontinued Now, We recommend other best selling Power Modules as a suitable replacement. A small, but mighty po...

DF-DFR0079

This motor has a long (0.365" or 9.27 mm), D-shaped metal output shaft that matches the Pololu wheel 42x19mm and 32x7mm. The brass faceplate has...

DF-FIT0302

A multi-use wrench used for installing the screws nut of the mobile platforms or the 3D printers and other tasks is the cross wrench.Much like a...

DF-FIT0306

Herkulex DRS-0101 is state of the art modular smart servos incorporating motor, gear reducer, control circutry and communications capabilit...

DF-SER0032

Like Arduino Mega/Due's IO, but bothered with the conflict of I/O pins when using shields with the Mega board during a project? Find it hard to ...

DF-DFR0256

The AA boost Module is DFrobot's exclusive product. One of its key features is solving the 5V battery power supply problem. As we all know, one AA...

DF-DFR0250

This 500 mm Y-cable is typically used to connect two servos to a single servo port on an RC receiver or servo controller. It has a single female...

DF-FIT0335

Light, thin and versatile solar panel at 1.5V/250MA. Unlike regular solar panels, it is truly flexible to be bent, sewed or treated in the clothin...

DF-FIT0333

This is a built-in GPS Antenna for DFRobot LEA-6H GPS shield. This GPS Antenna also have amplifing function. Its SMA male header can adapt to mo...

DF-TEL0042

Super hard screwdriver head mady by HSS high alloy steel,wear and distortion resisting! Purifier handle made by aluminum alloy...

DF-FIT0339

These customized colored pin headers are extensively used in DFRobot's product range. For instance, we are the first who uses 3 colors to clearl...

DF-FIT0342

These nylon cable ties will help you bundle up things and make your project tidy. Each comes in white color. They are: Faster - low inser...

DF-FIT0344

The DFRobot Relay Module is a standard relay used with a controller board to interface external electrical circuits or modules. Some of the most c...

DF-DFR0017

The upgraded Arduino Input Shield includes a two axis mini joystick (with moment switch) as well as four colored push buttons(Red,Yellow,Blue,Gr...

DF-DFR0008