Little Bird

The ESP8266 is now available in Australia. The new four-layer board design has a new revision antenna RF performance optimisation, compared to the ...

LB-LR0214-80A

Including CNC Shield V3.0The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.It has...

LB-LR0180

 Raspberry Pi micro-HDMI to HDMI A (male) cable allows you to connect your brand new Raspberry Pi 4 to your HDMI capable monitor or television.Micr...

PT-PT22018

Crack the Code™️ V2.0 Kit (No Arduino or Shield) The Crack the Code™️ V2.0 Kit provides all the essential components needed to build ...

LB-CTC-2-KIT-NO-ARDUINO

Great for hooking up your Raspberry Pi to a VGA monitor!This HDMI Male to VGA Female adapter cable lets you connect a standard analog monitor, proj...

LB-LR0293-5

This case provides your Arduino R3 Uno with an extra level of protection.  Made out of clear blue plastic and with block compatible moulding you ca...

LB-LS0439

USB-A to Micro Usb Cable 80cm Micro USB connectors are about half the height of mini USB. Micro USB is found on newer hand held devices like cell p...

LB-LR0293-3

M3 Nylon Screw Black Hex Screw Nut Nylon PCB Standoff Assortment Kit 250pcsM3*6+6mm        25pcsM3*8+6mm        25pcsM3*10+6mm      25pcsM3*12+6mm ...

LB-LS0513

We also stock the Basic Companion Kit to go with this book What is micro:bit in Wonderland?   micro:bit in Wonderland is a project book where you r...

LB-TK-ALICE

This is a touch sensor for Arduino.   This sensor is a toggle output type: touch-on then touch-off. Onboard TTP223 touch capacitive touch sensor...

LB-LR0214-47

The Little Bird Toucan is an smart RGB LED HAT designed for the Raspberry Pi! Based on the APA102, the Toucan packs 8 super-bright LEDs.Each of the...

LB-TOUCAN

Ready to use with pre-soldered anode and cathode with 5 inch wires.  Great for DIY projects!Operating Voltage:1.5VCurrent:400mAPeak Power:0.65WDime...

LB-SOLAR

Mini Wireless Keyboard 2.4G for use with the Raspberry Pi Add a good quality, slim chiclet keyboard as well as an track-ball mouse to your Raspberr...

LB-TRACK

These are two pin jumpers (also called shunts) that will create an electrical connection for the 2.54mm(0.1") male pin headers.  The Crack the Co...

LB-CTC-CAPS

This is an affordable 4-port USB 3.0 Hub.Specifications: Colour: Black Material: ABS Dimension: 105 x 37 x 23(mm) Cable Length: Approx. 30cm Blue i...

LB-LS0322

Perfect for your Lilypad wearable projects. This is a one meter length of soft conductive thread.  Enough to sew together your LEDs and battery for...

LB-LR0309-45

This 5m length of EL wire (electroluminescent wire) is a flexible wire coated with phosphor which glows blue when applied with the appropriate volt...

LB-LR0281-5-W

An ATmega328 in DIP package, pre-loaded with the Optiboot Bootloader.This will allow you to use code in your custom embedded project without having...

LB-PT9012

These soft rubber cases will protect your micro:bit while also looking super cute!It is made from hard-wearing, soft, flexible rubber, making it ea...

LB-LS0818-RED

The Raspberry Pi 3 GPIO Reference Card made by Little Bird (Australia) makes it quick and easy to understand what pins do what on your RPI3. Altho...

LB-RPI3-GPIO-REFERENCE

We’ve all seen toys and things that change color when you run them under warm water or heat them up in the sun. Some of us were especially mesme...

LB-00258