Prototyping in New Products

This is a K type Thermocouple (Temperature sensor) which is very popular for 3D printers such as Ultimaker and Makerbot. You can hardly damage t...

DF-SEN0139

This is a very simple but handy, 2" square, double sided perf board. Standard 0.1" spacing with a 4-40 (3mm) holes for mounting. Great for quickly ...

SF-PRT-08811

This is the FeatherWing Doubler - a prototyping add-on and more for all Feather boards. This is similar to our FeatherWing Proto except there are t...

AF-2890

This is a very simple but extremely handy, 1" square, single sided perf board. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every thr...

SF-PRT-08808

The smallest and easiest to use serial conversion circuit on the market! This board has one purpose in life - to convert RS232 to TTL and vice vers...

SF-PRT-08780

These are 8mm (0.31") copper sleeves that will slide perfectly onto 8mm (0.31") rods. Perfect for your 3D printer prototyping needs! S...

DF-FIT0233

This is a 300MXL Timing belt. It was commonly used in 3D printer such as Reprap and ultimater. SPECIFICATIONS Type:B300MXL L...

DF-FIT0236

This is a B100MXL Timing belt which is commonly used in 3D printer or CNC machine. SPECIFICATIONS Type:B100MXL LP:203.20mm ...

DF-FIT0235

This is a SOP16/SOP28/SSOP28 to DIP16/DIP28 Adapter Board.You can change the SOP16/SOP28/SSOP28 to DIP16/DIP28 packaging.So that You needn't to ...

DF-FIT0291

This is a SOP8 to DIP8 Adapter Board. You can change the SOP8 to DIP8 packaging.So that You needn't to buy the DIP chips for prototyping special...

DF-FIT0290

SPECIFICATIONS Type: LM6UU Inner diameter: 6mm (0.24") Outer diameter: 12mm (0.47") Length: 35mm (1.38") SHIPPI...

DF-FIT0239

This is a black braided cable guide. The braid provides some rigidity to the cables, also, it can be expanded by compressing it which will allo...

DF-FIT0250

This is 1 meter of PFA tubing with a 6mm diameter. PFA has a high temperature resistance with a melting point of 305C. This tubing is used as a ...

DF-FIT0243

Three pin JST connector with red, black, and yellow colors. 5 inch wire outs. This cable comes fully assembled as shown and connects directly to ma...

SF-SEN-08733

This is a high quality PEEK insulator and PTFE-PFA adapter for isolating the heat generated from the heater block of a 3D printer's extrude...

DF-FIT0254

This is a very basic double sided prototyping board with standard 0.1" spacing with a 4x3mm (0.16x0.12") holes for mounting.The leaf pads m...

DF-FIT0193

This kit includes JST XHP-2, XHP-3 and XHP-4 housing (20 units each), through-hole type shrouded header (20 units each) and crimp contact (100 un...

DF-FIT0255

This is a 600mm (23.62") servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on th...

DF-FIT0297

This is a 150mm (5.91") servo extension cable. This comes in very handy when your servo is further away from the controller than the wire on the s...

DF-FIT0296

This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opposite end. Dimensions...

SF-PRT-08671

This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opposite end. Dimensions...

SF-PRT-08670

This kit includes PHR-2, PHR-3 and PHR-4 housing (20 units each), through-hole type shrouded header (20 units each) and crimp contact (100 uni...

DF-FIT0299