Prototyping in New Products

This mounting bracket is designed for Sharp GP2D12/2D15/Sharp GP2Y0A02YK IR ranger sensor. You can buy this item using 250 reward points. S...

DF-FIT0005-OE

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS Screw...

DF-FIT0270

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIO...

DF-FIT0294

An empty canvas for electrical enthusiasts! Designed to fit the SFE project enclosures this project board gives you 8x10cm (3.15x3.94") of building...

SF-PRT-08619

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS   ...

DF-FIT0273

This is the same accessory cable found in the LIDAR-Lite v3. The LIDAR-Lite Accessory Cable is terminated with a simple 6-pin JST at one end and a ...

SF-CAB-14043

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIO...

DF-FIT0280

This is a simple two wire cable. One end has a 2 pin female 0.1" pitch connector. Opposite end has 2-pin JST connector. Dimensions: 130mm Documen...

SF-PRT-08599

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATION   ...

DF-FIT0274

This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, 2-pin Molex 0.1" pitch polarized connector ...

SF-PRT-08598

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS   ...

DF-FIT0269

The Pimoroni Explorer HAT Pro is a “shield” for the Raspberry Pi and provides you with the perfect prototyping sidekick for your Pi. The Explorer H...

SF-DEV-14039

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIO...

DF-FIT0281

If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The Lithium Battery Charger can charge 3.7V LiPo ba...

DF-DFR0208

This 0.012" Flexinol® Actuator Wires (aka shape memory Nitinol) is a one foot long piece of nickel-titanium alloy that can flex and contract when a...

SF-COM-12096

This 0.005" Flexinol® Actuator Wires (aka shape memory Nitinol) is a one foot long piece of nickel-titanium alloy that can flex and contract when a...

SF-COM-12095

Simple IDC ribbon cable. Used for AVR programming, general communication, and all around handy-ness. Datasheet shows an incorrect length. Cable l...

SF-PRT-08535

This crystal kit include 7 common value crystals.If you do not sure what crystal you may need, get this package of all most common values for yo...

DF-FIT0295

This Yellow green ligth bar has a high quality, low pwer consumption LED.The KWL-R151 series is 13x13mm light bar display, designed for viewing ...

DF-FIT0288-YG

This is the SparkFun Solderable Breadboard. A bare PCB that is the exact size as our regular breadboard with the same connections to pins and power...

SF-PRT-12070

This is a blue colored 40 Pin 2.54 mm Single Row Pin Header Strip from DFRobot. These 0.1" header strips are commonly used as low-cost Arduino c...

DF-FIT0084-Y

This is a high quality PTFE-PFA adapter for isolating the heat generated from the heater block of a 3D printer's extruder. PTFE(polytetraflu...

DF-FIT0307

 INTRODUCTIONThese are 7.8"(20cm) long jumper wires terminated as male to female. Use these to jumper from any female header on any board such as A...

DF-FIT0301