Sensors in New Products

This is a nice metal 315MHz remote wireless keyfob with high electromagnetic conversion, strong emission power and low power consumption. It use...

DF-FIT0355

IR sensor tuned to 38KHz, perfect for receiving commands from a TV remote control. Runs at 3V to 5V so it's great for any microcontroller.To use, c...

AF-157

Hall effect sensors detect whether a magnet is near. Useful for non-contact/waterproof type switches, position sensors, rotary/shaft encoders. I tr...

AF-158

The MyoWare LED Shield is designed to pair with the MyoWare Muscle Sensor. The blue 10-segment bar graph shows the magnitude of the measured signal...

SF-DEV-13688

Overview This board is a compact (0.4″ × 0.9″) breakout board for ST’s L3GD20H three-axis digital-output gyroscope; we therefore recommend car...

PL-2129

Piezo buzzers are used for making beeps, tones and alerts. This one is petite but loud! Drive it with 3-30V peak-to-peak square wave. To use, conne...

AF-160

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at l...

DF-DFR0029-R

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at l...

DF-DFR0029-W

The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board i...

SF-DEV-13684

CdS cells are little light sensors. As the squiggly face is exposed to more light, the resistance goes down. When its light, the resistance is abou...

AF-161

The SHT15 Breakout is an easy to use, highly accurate, digital temperature and humidity sensor. This board has been fully calibrated and offers hig...

SF-SEN-13683

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at lef...

DF-DFR0029-B

This SHARP distance sensor bounces IR off objects to determine how far away they are. It returns an analog voltage that can be used to determine ho...

AF-164

Overview This board is a compact (0.4″ × 0.9″) breakout board for ST’s LSM303D e-compass module, a single IC featuring a 3-axis digital linear a...

PL-2127

Press to release pleasure! Our redesigned digital push buttons come with LED, immersion gold surface, and bright colored hats. A captital D at l...

DF-DFR0029-G

Wide range, low power temperature sensor outputs an analog voltage that is proportional to the ambient temperature. To use, connect pin 1 (left) to...

AF-165

FSRs are sensors that allow you to detect physical pressure, squeezing and weight. They are simple to use and low cost. This sensor is a Interlink ...

AF-166

DFRobot WiFi Shield for Arduino, is part of our wireless family product. This WIFI Shield V3 supports AP + STA dual mode, and is extremely easy ...

DF-TEL0079

Overview This board is a compact (0.4″ × 0.9″) carrier for ST’s LPS331AP MEMS absolute pressure sensor, or barometer; we therefore recommend c...

PL-2126

DFRobot WiFi Shield, is part of our wireless family product. This WIFI Shield V3 supports AP + STA dual mode, and is extremely easy to connect t...

DF-TEL0078

This is an Arduino Temperature Sensor based on LM35 temperature chip. A Temperature Sensor can be used to detect ambient air temperature. The LM35...

DF-DFR0023

The SparkFun BME280 Atmospheric Sensor Breakout is the easy way to measure barometric pressure, humidity, and temperature readings all without taki...

SF-SEN-13676

LV-EZ1 Maxbotix Ultrasonic Rangefinder provides very short to long-range detection and ranging, in an incredibly small package. It can detect objec...

AF-172