New Products

The SparkFun Inventor’s Kit for RedBot is a great way to get started with two motor robotics and sensor integration using the Arduino programming l...

SF-ROB-12649

An electrolytic capacitor uses an electrolyte (a liquid or gel containing a high concentration of ions) to achieve a large capacitance than...

TB-RE6314

This is essentially a ramped up version of our Ardumoto motor driver shield. For this SparkFun Monster Moto Shield we’ve replaced the L298 H-bridge...

SF-DEV-10182

These modules are for use in circuit designs incorporating the use of Smard Cards / IC Cards. They accept either card and feature an intern...

TB-PS0010

INTRODUCTION This cable will supply power to anything that has a MicroUSB port. The cable does not transfer data, but it...

DF-FIT0459

These surface-mount LEDs are an easy way to add a lot of bright white dots to your project. They're similar to the ones in our digital RGB LED stri...

AF-682

0.1" connector custom cable. These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connect...

PL-1865

Repair or design your very own audio cables with these nice and durable phono-jack connectors. This is a great jack to make your own 1/4" stereo ca...

AF-1804

Protects cabling, neat and tidy, and protects from abrasion, wear and tear using this flame resistant self closing wrap. Each 2m length is ...

TB-WH5632

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a...

AF-3428

Overview Pololu High-Current Motor Driver Carrier pinouts and dimensions. This module is a compact breakout board for ST’s high-power VNH2SP...

PL-706

You might have seen these cables used in computers. They are typically used to bring USB connections from a motherboard to the external case, or th...

SF-CAB-10177

- (6.35 x 30mm) - 10A

TB-SF2204

RGB Pixels are digitally-controllable lights you can set to any color, or animate. Each metal 'pixel square' contains 4 RGB LEDs and a controller c...

AF-683

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features: 600-610nm Orange ...

SF-COM-12645

INTRODUCTION This RTC module is specifically designed for the Raspberry Pi. It communicates with Raspberry Pi through I2C bus and includes a Maxim ...

DF-DFR0386

Overview These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-...

PL-3064

Here we have some conductive ribbon. Essentially, it’s a fabric with 3 conductors woven into the ribbon. It measures roughly 0.2" wide and 0.03" th...

SF-DEV-10172

OPA2134PA OPAMP AUDIO HI PERF DIP8 IC Specifications active mount type Throug...

TB-ZL3972

0.1" connector custom cable. These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connect...

PL-1864

The TSL2561 luminosity sensor is an advanced digital light sensor, ideal for use in a wide range of light situations. Compared to low cost CdS cell...

AF-439

Overview Pololu High-Current Motor Driver Carrier pinouts and dimensions. This module is a compact breakout board for ST’s high-power VNH2SP...

PL-705

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides ...

SF-SEN-12642

Protects cabling, neat and tidy, and protects from abrasion, wear and tear using this flame resistant self closing wrap. Each 2m length is ...

TB-WH5634