Not Zero Margin Goods

This is a simple two wire cable. One end has a 2-pin 0.1" pitch female connector, the opposite end is stripped and tinned stranded wire. Dimension...

SF-PRT-08672

This basic sumo blade (sometimes also called a “scoop”) is intended for use with the Zumo chassis and included as part of the assembled Zumo Robot...

PL-1410

This is a simple two wire cable. Both ends have a 2-pin 0.1" pitch female connector. Dimensions: 130mm length

SF-PRT-08614

These are very small surface mount quartz crystals used where size is a concern. 24MHz for maximum speed. Note: The datasheet below is a generic d...

SF-COM-08581

Horizontal surface mount connector for the EB-85A/FV-M8 GPS receiver. Documents:EB-85A-Connector.pdf

SF-GPS-08297

The SparkFun Inventor’s Kit (SIK) is a great way to get started with programming and hardware interaction with the Arduino programming language. Th...

SF-KIT-13970

This is the itty-bitty connector for the Nokia color LCD. 10-Pins. Surface mount. Hard to find. 0.5mm pitch so be careful. Can it be soldered by ...

SF-LCD-00570

Resonators function like crystals but stick closer to their specified frequency over a full temperature range. These resonators are +/-0.5% or bett...

SF-COM-00542

DFRobot proudly presents the I/O expansion shield for Texas Instruments MSP430 LaunchPad. With the I/O expansion shield, your LaunchPad will be ...

DF-DFR0257

This is not your typical temperature sensor. The TMP006 Breakout can measure the temperature of an object without making contact with it. By using ...

SF-SEN-11859

Using an OctoBrite to control the color and brightness of multiple satellite modules. The 003 and 004 satellite modules from Macetech have ...

PL-1245

Overview The ShiftBar is a 3-channel constant current LED driver module by macetech based on the Allegro A6281. This is a carrier board that is s...

PL-1242

The SparkFun PicoBoard Starter Kit is your go-to source to begin learning everything about the SparkFun PicoBoard and the Scratch programming envir...

SF-KIT-13863

The microUSB Programming Adapter (μUSB-PA5) is a USB to Serial-TTL UART bridge converter which is very small and easy to use. It uses a mini-B type...

SF-DEV-11814

8-Pin SSOP to DIP break out board. The footprint was rotated to accommodate different width SSOP devices and can be used with 8 pin SSOPs. Designed...

SF-BOB-00497

This adjustable infrared sensor features a high-sensitivity photoreflector to perform distance detection function,ranging from 3cm to 50cm. When...

DF-SEN0164

Want to free your pcDuino from the oppression of wired networking? This USB Wifi dongle has been tested to work with the pcDuino, simply plug it in...

SF-WRL-11713

Overview The GP2Y0D805, GP2Y0D810 , and GP2Y0D815 are Sharp’s smallest and fastest distance sensors, and this tiny carrier board for these se...

PL-1133

Overview These brushed DC gearmotors are compact and affordable — perfect for building a quick, miniature robot. They are intended for use at 4.5...

PL-1125

The Fio v3 is a new spin on the Arduino Fio hardware powered by the ATmega32U4.Not only is it small and LiPo-ready, it’s a very capable XBee-ready ...

SF-DEV-11520

Crimpless but strong BNC plugs for low volume applications. Specifications Plug or Socket Type ...

TB-PP0678

These knobs just push on to a standard 0.25 (1/4) shaft. - No more messy screws. - Complete with coloured cap. S...

TB-HK7711

These knobs just push on to a standard 0.25 (1/4) shaft. - No more messy screws. - Complete with coloured cap. S...

TB-HK7715

This is the SparkFun Photon IMU Shield, a versatile motion-sensing add-on board for your Photon device. Each IMU shield is equipped with an on-boar...

SF-DEV-13629

The SparkFun Photon Micro OLED Shield breaks out a small monochrome, blue-on-black OLED to use with your Photon module. It’s “micro”, but it still ...

SF-DEV-13628