Prototyping

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield. Strong self-adhesive backing. Me...

DF-FIT0008-BK

This is the very first prototyping shield for Arduino in the market since 2010. It comes with prototyping area that you can sold led , switch o...

DF-DFR0019

These are two pin jumpers (also called shunts) that will create an electrical connection for the 2.54mm(0.1") male pin headers. Commonly used to m...

DF-FIT0140

This is an Emergency stop switch(Mushroom switch, push button switch). This is a great looking button for any project where you need a "Big Red ...

DF-FIT0156

This is a 4.7 Farad capacitor. This small cap can be charged up and then slowly dissapated running an entire system for hours. Combine two in se...

DF-FIT0133

A prototyping board is one of the main steps in hardware development, also called a perf board. Breadboard, wiring and punching in chips, resistor...

DF-FIT0099

The name says it all on this one. An ATmega328 in DIP package, pre-loaded with the Arduino (16MHz) Bootloader. This will allow you to use Arduino ...

DF-DFR0081

The Gravity 4Pin IIC/I2C/UART sensor cable is a standard Gravity series 4-Pin cable with 30cm length. One side is PH2.0-4p connector and the oth...

DF-FIT0513

The analog sensor cables are especially designed for our popular IO Expansion shield and sensors. It connects most of our analog sensor to the I...

DF-FIT0031

This is a very small breadboard with 170 tie points. This bread board is compatible with the Arduino Proto Shield shown below. Strong, self-adhe...

DF-FIT0008

INTRODUCTION The digital sensor cables are especially designed for our popular IO Expansion shield and sensors. It con...

DF-FIT0011

Polyimide Tape (sometimes referred to by the brand name Kapton Tape) is an interesting addition to your toolbox! Polyimide Tape remains stable acro...

AF-3057

This spool of solid-core wire is easily soldered to and can handle up to 200°C and 600V. We like this wire because it's flexible but also holds its...

AF-2990

This spool of solid-core wire is easily soldered to and can handle up to 200°C and 600V. We like this wire because it's flexible but also holds its...

AF-2989

This spool of solid-core wire is easily soldered to and can handle up to 200°C and 600V. We like this wire because it's flexible but also holds its...

AF-2986

This spool of solid-core wire is easily soldered to and can handle up to 200°C and 600V. We like this wire because it's flexible but also holds its...

AF-2984

This cute hard-covered booklet will make storing your SMT parts a breeze with translucent flip-pages that are designed for keeping taped parts. The...

AF-520

Beguiled by a fancy new chip that is only available in a SOIC or MSOP/(T)SSOP pinout? This breakout PCB set will make your life much much easier an...

AF-1212

Customers have asked us to carry basic perf-board, but we never liked the look of most basic perf: its always crummy quality, with pads that flake ...

AF-1606

Always have the right SMT components at your hand with this awesome 0805 Resistor and Capacitor book set! This book has nice translucent pages fill...

AF-441

Kiss those days of heat-shrink, melted jacketing and clumsily-arranged third-hand tools goodbye! Go 'cold splice' with these snap-able plastic spli...

AF-1494

Finally, the conductive material you've known you wanted but never knew you could have, its a sheet of flex PCB material! This is the stuff used to...

AF-1894

This stuff is called "wire-wrap wire" because it used to be used for wire-wrapping high-speed digital circuits on a special kind of contact board. ...

AF-1446

Pogo pins are little spring-loaded contacts, very handy for making jigs, or making momentary (but electrically solid) contacts. We use them by the ...

AF-2429