Robotics

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of ...

DF-DFR0430

Overview This hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 500 mA at 10 V, allowing for a holding ...

PL-1208

A4983/A4988 stepper motor driver carrier with dimensions. Overview This product is a carrier board or breakout board for Allegro’s A4988 DMO...

PL-1182

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the int...

DF-DFR0457

Overview This kit includes two dual-channel Hall Effect sensor boards and two 6-pole magnetic discs that can be used to add quadrature encoding to...

PL-3081

This all purpose hobby motor will run from 3v to 6v at around 4,000 - 8,000RPM and is great for your fan powered car or other small robotics projec...

LB-LR0244

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil ...

AF-3992

When your little robot needs someone to lean on, it can lean on this support wheel. Perfect for use with 2-wheeled robots that need a third-point o...

AF-2942

These universal mounting hubs are designed to work with most 6 mm diameter shafts, including round shafts and “D” shafts. Each of the two include...

PL-1083

This version of our Black Edition A4988 Stepper Motor Driver Carrier ships with 0.1″-pitch male header pins installed as shown in the main product...

PL-2981

Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition to your robotic gardening project. There are t...

AF-997

These motorized sliders are very cool. Each is essentially a standard slide pot which is belt-driven by a small motor. The slide contains two separ...

SF-COM-10976

Pololu ball caster with 3/8" metal ball with included hardware. Overview This ball caster kit includes a black ABS housing, a 3/8″ diameter ...

PL-951

These universal mounting hubs are designed to work with most 8 mm diameter shafts, including round shafts and “D” shafts. Each of the two include...

PL-2693

This ball caster is an improved version of our original Pololu Ball Caster with 1″ Plastic Ball; we recommend this new version over the older vers...

PL-2691

USB Micro-B connector breakout board, bottom view with dimensions. This board breaks out the VBUS, GND, D-, D+, and ID pins of a USB Micro-B...

PL-2586

Overview These terminal blocks have terminals that hold and release wires through the simple adjustment of a screw, allowing you to easily make te...

PL-2446

This is a mounting bracket designed for our URM ultrasonic sensor series.It is fully compatible with URM37 and URM04. You can also have this i...

DF-FIT0006

This is a really easy use prototyping plate. Basically you can put everything from Arduino board to sensors, even a motor on top of it. It fits M2...

DF-FIT0101

The SparkFun Servo Trigger is a small robotics board that simplifies the control of hobby RC servo motors. When an external switch or logic signal ...

SF-WIG-13118

Note: The QTR-1A reflectance sensor requires an analog input to take readings. The similar QTR-1RC reflectance sensor is available with a digita...

PL-2458

A4988 stepper motor driver carrier, Black Edition, bottom view with dimensions. Overview This product is a carrier board or breakout board f...

PL-2128

Overview This ball caster kit includes a black ABS housing, a 3/4″ diameter metal ball, two spacers (1/16″ and 1/8″ thick), and two #2 screw s...

PL-955

A Feather board without ambition is a Feather board without FeatherWings! This is the 8-Channel PWM or Servo​ FeatherWing, you can add 8 x 12-bit P...

AF-2928

This lightweight (about 7.5 g) but strong bracket is made from 2mm-thick black anodized aluminum and is specifically designed to work with the...

PL-2257

Arduino Leonardo, top view. Arduino Leonardo, bottom view. Note: There are differences between the Leonardo and previous Arduino boards. As...

PL-2192

This uneven terrain traveling hexapod comes with eighteen(18) CDS5516 high performance 300 degree rotation servos which gives this hexapod 18 degr...

DF-ROB0080

Overview The AR-3606HB is a standard-sized servo that has been built by Power HD specifically for continuous rotation. At 6 V, it has a maximum ro...

PL-2149

This is a great general-purpose actuator for tiny mechanisms. The lead is terminated with a standard “JR”-style connector, which is Futaba-compat...

PL-2145

Big brain. Bigger personality.Say hello to Cozmo, a gifted little guy with a mind of his own. He’s a real-life robot like you’ve only seen in movie...

MG-000-00067

Drive The Fast & Furious.These aren’t just cars and tracks; these are robots programmed for battle and controlled with your mobile device. Batt...

MG-000-00068

Micro servo motor, perfect for use with XC4618 Pan and Tilt bracket. Small enough to connect directly to an Arduino Board for experimenting.-500 d...

TB-YM2758

These clear nylon screws and nuts can be used to fix your circuit board, sensors and mechanical mountings. Used in applications where moderate s...

DF-FIT0195

USB A to Micro-B cable size comparison: standard cable (#2073) on left, thin cable (#2072) on right. This USB cable is six feet long (1.8 m)...

PL-2073

CLEARANCE PRICE - ONLY FOR IN-STOCK ITEMS RRP  $7.60 Use this cable to connect two servo to Grove system with only 1 cable. Compatible w...

SS-110990057

These universal mounting hubs are designed to work with most 6 mm diameter shafts, including round shafts and “D” shafts. Each of the two include...

PL-1999

PL-1960

This MiniQ motor wheel set is especially designed for education and hobbies. It features a powerful metal gear motors which provide a speedy rob...

DF-KIT0015

PL-1957

This is the Wheel Encoder Kit from DAGU, a simple add-on to any wheeled robot that can help measure the speed or distance the chassis travels. Each...

SF-ROB-12629

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIONS   ...

DF-FIT0273

RoMeo V2 [R3] is an All-in-One Arduino based robot board, it is especially designed for robotics applications, and extended devices. Romeo benef...

DF-DFR0225

Move fluid from here to there with this very nice elastomeric silicone tubing, specifically for our peristaltic pump. It's one meter long and fully...

AF-3659

Overview These M-F (male-female) aluminum standoffs are great for separating stacked components or chassis tiers. Each hexagonal standoff is ...

PL-1940

These are M3 hex head cap screw, which provides a more secure way to install circuit boards, sensors and mechanical mounting. SPECIFICATIO...

DF-FIT0281

Romeo family is an All-in-One Arduino based control board especially designed for robotics applications from DFRobot. It benefits from the Ardu...

DF-DFR0305

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil ...

AF-413

Overview These cylindrical brushed DC gearmotors are available in a wide range of gear ratios and with five different motors (two power levels of ...

PL-1591