Robotics

INTRODUCTION An ordinary DC motor requires an H Bridge to work with a microcontroller such as an UNO. For newcomers to electronics, the process of ...

DF-DFR0430

Overview This hybrid bipolar stepping motor has a 1.8° step angle (200 steps/revolution). Each phase draws 500 mA at 10 V, allowing for a holding ...

PL-1208

A4983/A4988 stepper motor driver carrier with dimensions. Overview This product is a carrier board or breakout board for Allegro’s A4988 DMO...

PL-1182

In most Arduino projects, relays are the first choice to drive some large current device. It requires a certain amount of current to drive the int...

DF-DFR0457

Overview This kit includes two dual-channel Hall Effect sensor boards and two 6-pole magnetic discs that can be used to add quadrature encoding to...

PL-3081

This all purpose hobby motor will run from 3v to 6v at around 4,000 - 8,000RPM and is great for your fan powered car or other small robotics projec...

LB-LR0244

Solenoids are basically electromagnets: they are made of a big coil of copper wire with an armature (a slug of metal) in the middle. When the coil ...

AF-3992

When your little robot needs someone to lean on, it can lean on this support wheel. Perfect for use with 2-wheeled robots that need a third-point o...

AF-2942

These universal mounting hubs are designed to work with most 6 mm diameter shafts, including round shafts and “D” shafts. Each of the two include...

PL-1083

This version of our Black Edition A4988 Stepper Motor Driver Carrier ships with 0.1″-pitch male header pins installed as shown in the main product...

PL-2981

Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition to your robotic gardening project. There are t...

AF-997

These motorized sliders are very cool. Each is essentially a standard slide pot which is belt-driven by a small motor. The slide contains two separ...

SF-COM-10976

Pololu ball caster with 3/8" metal ball with included hardware. Overview This ball caster kit includes a black ABS housing, a 3/8″ diameter ...

PL-951

These universal mounting hubs are designed to work with most 8 mm diameter shafts, including round shafts and “D” shafts. Each of the two include...

PL-2693

This ball caster is an improved version of our original Pololu Ball Caster with 1″ Plastic Ball; we recommend this new version over the older vers...

PL-2691

USB Micro-B connector breakout board, bottom view with dimensions. This board breaks out the VBUS, GND, D-, D+, and ID pins of a USB Micro-B...

PL-2586

Overview These terminal blocks have terminals that hold and release wires through the simple adjustment of a screw, allowing you to easily make te...

PL-2446

This is a mounting bracket designed for our URM ultrasonic sensor series.It is fully compatible with URM37 and URM04. You can also have this i...

DF-FIT0006

This is a really easy use prototyping plate. Basically you can put everything from Arduino board to sensors, even a motor on top of it. It fits M2...

DF-FIT0101

The SparkFun Servo Trigger is a small robotics board that simplifies the control of hobby RC servo motors. When an external switch or logic signal ...

SF-WIG-13118

Note: The QTR-1A reflectance sensor requires an analog input to take readings. The similar QTR-1RC reflectance sensor is available with a digita...

PL-2458

A4988 stepper motor driver carrier, Black Edition, bottom view with dimensions. Overview This product is a carrier board or breakout board f...

PL-2128

Overview This ball caster kit includes a black ABS housing, a 3/4″ diameter metal ball, two spacers (1/16″ and 1/8″ thick), and two #2 screw s...

PL-955

A Feather board without ambition is a Feather board without FeatherWings! This is the 8-Channel PWM or Servo​ FeatherWing, you can add 8 x 12-bit P...

AF-2928