Sensors

INTRODUCTION This is the XBee XBP24CZ7WIT-004 module from Digi. The new Series 2C improves upon the power output and dat...

DF-TEL0017

This is a waterproof DC-DC converter. With 8-40V DC input, it converts to 12V@6A which is ideal supply for embedded PC and robot power. SPE...

DF-FIT0145

The ETH008 provides eight volt free contact relay outputs with a current rating of up to 16Am. The module is powered from a 12vdc supply which c...

DF-DFR0146

This precision sensor from Bosch is the best low-cost sensing solution for measuring barometric pressure and temperature. Because pressure changes ...

AF-1603

This inertial-measurement-unit combines 3 of the best quality sensors available on the market to give you 11 axes of data: 3 axes of accelerometer ...

AF-1604

The Arduino Wireless SD Shield provides a 3.3v regulated Digi Xbee slot for easy wireless connectivity, a uSD (micro Secure Digital) slot for on...

DF-DFR0152

This is a BH1750 light intensity sensor breakout board with a 16 bit AD converter built-in which can directly output a digital signal, there is no...

DF-SEN0097

This is the LilyPad Arduino Simple Board. It's controlled by an ATmega328 with the Arduino bootloader. It has fewer pins than the LilyPad Arduin...

DF-DFR0168

DFRobot is very proud to release this first 802 b/g/n wifi shield in the Arduino market. The arduino shield uses WizFi210 which is a low power-...

DF-TEL0047

This is a simple breakout board for the SHT15 humidity sensor from Sensirion. The SHT15 digital humidity and temperature sensor is fully calibrated...

AF-1638

A low power version of the USB-RLY16 module, the USB-RLY16L is powered solely from the USB bus and provides eight volt free contact relay output...

DF-DFR0173

This breakout board uses the LTC3588 Piezoelectric Energy Harvester from Linear Technologies. This board can be used not only for harvesting pie...

DF-SEN0105

This is an edge detection sensor from DFRobot. It will help your robot detect the edge of a precipice, preventing it from falling off a table or...

DF-SEN0042

Sparkle is Aniomagic's avant-garde way to make interactive textiles, paper, ceramics, and environments. These lightboards come in packs of five ...

DF-DFR0169

Sabertooth 2X5 is the motor driver of choice for small differential-drive robots. It is ideal for smaller robots- up to 3lbs in combat or 25 lbs...

DF-DRI0012

This is a waterproof DC-DC converter. With 8-18V DC input, it converts to 24V@10A which is an ideal supply for robots. FEATURES ...

DF-FIT0172

This is a waterproof DC-DC converter. With 8-40V DC input, it converts to 24V@6A which is an ideal supply for mobile robots, and motors. ...

DF-FIT0171

This is a waterproof DC-DC converter. With 12-40V DC input, it converts to 12V@10A which is an ideal supply for embedded PC and robots. ...

DF-FIT0170

This is a waterproof DC-DC converter. With 16-36V DC input, it converts to 9V@5A which is a good supply for robots. FEATURES ...

DF-FIT0169

This is a waterproof DC-DC converter. With 12V/24V (11-35V) DC input, it converts to 7.5V@5A which is an ideal supply for robots. FE...

DF-FIT0168

Overview This board is a compact (0.4″ × 0.9″) breakout board for ST’s L3GD20H three-axis digital-output gyroscope; we therefore recommend car...

PL-2129