SparkFun Australia

These flat bearing mounts attach to the face of a channel or plate and have a ball bearing with a 5/8” bore for shafts. They can be used in conjunc...

SF-ROB-12554

These 4" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". When used with the mat...

SF-ROB-12553

These clear pink precision disk wheels have an outer diameter of 5”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are i...

SF-ROB-12552

These aluminum channels are the building blocks to the Actobotics line and function as the back bone to your electromechanical project. These chann...

SF-ROB-12551

We all know that you can never get too many LEDs. Don’t worry, we’ve got you covered. This is a pack of 25 LEDs all conveniently packaged in a nice...

SF-COM-09856

These 7" long stainless steel shafts have a diameter of 1/8". These shafts are solid, which makes them an ideal choice for axles. These shafts have...

SF-ROB-12550

These lipped Rubber Rings have an inner diameter of 3.65", a width of 1/8", and a sturdy rubber sidewall. These rings can be used as a replacement ...

SF-ROB-12549

These 12" long stainless steel D-Shafts have a diameter of ¼". The flat edge that runs the length of the shaft makes it an ideal drive shaft, when ...

SF-ROB-12548

These 8" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". When used with the mat...

SF-ROB-12547

These aluminum double servo arms have a length of 2.685”, a width of 0.25”, and utilize the 0.77” hub pattern that can connect directly to your C1 ...

SF-ROB-12546

These 9" long stainless steel shafts have a diameter of 1/8". These shafts are solid, which makes them an ideal choice for axles. These shafts have...

SF-ROB-12544

These lightweight servo hubs are ideal for attaching wheels, gears, or any heavy duty servo horns directly to your C1 Hitec servo spline. These alu...

SF-ROB-12543

These 5" long stainless steel shafts have a diameter of ½". These shafts are solid, which makes them an ideal choice for axles. These shafts have a...

SF-ROB-12542

Pillow block bearing mounts attach to the outside of a channel and can be used as simple hinges. These bearing mounts have a width of 1.32”, a thic...

SF-ROB-12541

These 2.375" long stainless steel D-Shafts have a diameter of ¼". The flat edge that runs the length of the shaft makes it an ideal drive shaft, wh...

SF-ROB-12540

These clear pink precision disk wheels have an outer diameter of 4”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are i...

SF-ROB-12539

These 6" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When used with the mating tub...

SF-ROB-12538

These black precision disk wheels have an outer diameter of 2”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are ideal ...

SF-ROB-12537

These 7" long stainless steel shafts have a diameter of 3/8". These shafts are solid, which makes them an ideal choice for axles. These shafts have...

SF-ROB-12536

These 1.0" long stainless steel D-Shafts have a diameter of ¼". The flat edge that runs the length of the shaft makes it an ideal drive shaft, when...

SF-ROB-12535

These skate wheel adapters have a diameter of 1”, a width of 0.32”, and utilize the 0.77” hub pattern. These adapters allow you to attach the 2.975...

SF-ROB-12534

These side mount brackets can function as mounts for encaps for Actobotics channels. They have two 6-32 tapped holes spaced 0.544" apart perpendicu...

SF-ROB-12533

These aluminum attachment blocks make it possible to connect two flat panels at a 90° angle. These blocks come in packs of 12 and each offers two 6...

SF-ROB-12531

This is a simple 5V Op Amp breakout board, set up as a 2-stage amplifier with a gain of 100 (gain of 10 for each stage). The on-board trim pot sets...

SF-BOB-09816

These orange precision disk wheels have an outer diameter of 2”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are ideal...

SF-ROB-12530

These pinion gears attach to a ¼” D-shaft or gear motor using a setscrew. They have 20 teeth with a gear pitch of 32P, an outer diameter of 0.688”,...

SF-ROB-12529

These zinc-plated socket head machine screws are 1"” long and have a tread pitch of 6-32. Sold in packs of 25. Note: These screws require a 7/64" ...

SF-ROB-12528

The ITG-3200 is the world’s first single-chip, digital-output, 3-axis MEMS motion processing gyro optimized for gaming, 3D mice, and motion-based r...

SF-SEN-09793

These 9" long stainless steel shafts have a diameter of ½". These shafts are solid, which makes them an ideal choice for axles. These shafts have a...

SF-ROB-12527

These smooth (round) belts have a Durometer hardness of A70 and can withstand temperatures from -35 to 250 degrees F. Their elastic nature allows t...

SF-ROB-12526

These zinc-plated socket head machine screws are 5/16” long and have a tread pitch of 6-32. Sold in packs of 25. Note: These screws require a 7/64...

SF-ROB-12525

This motor mount connects to other Actobotics products with a swivel mount, allowing you to easily attach your motor to gears or pulleys. A set scr...

SF-ROB-12524

These hub-mountable aluminum sprockets can be used to drive wheels or other sprockets with 0.25” chain. They have 40 teeth with a spacing of 0.25”,...

SF-ROB-12522

These 12" long aluminum tubes have an outer diameter of 5/8", an inner diameter of 0.569", and a wall thickness of 0.028". When used with the matin...

SF-ROB-12521

These 2" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When used with the mating tub...

SF-ROB-12520