SparkFun Australia

Quad hub mounts attach to the inside of a channel at a 90 degree angle providing you with additional attachment points for the open top of a channe...

SF-ROB-12349

The Qwiic Mux - PCA9548A enables communication with multiple I2C devices that have the same address and between different bus voltages (2.8V, 3.3V,...

SF-SPX-14293

The Qwiic Shield for Raspberry Pi connects the I2C bus (GND, 3.3V, SDA, and SCL) on the 40-pin Pi connector to the SparkFun Qwiic system. Just plug...

SF-SPX-14292

These 12" long aluminum tubes have an outer diameter of 3/8", an inner diameter of 0.30", and a wall thickness of 0.035". When used with the mating...

SF-ROB-12346

These 2.25" long stainless steel D-Shafts have a diameter of ¼". The flat edge that runs the length of the shaft makes it an ideal drive shaft, whe...

SF-ROB-12344

The 1Wire-to-Qwiic Bridge allows you to communicate via I2C over very long distances. It does so by utilizing the 1Wire communication protocol, whi...

SF-SPX-14291

These lipped Rubber Rings have an inner diameter of 1.65", a width of 1/8", and a sturdy rubber sidewall. These rings can be used as a replacement ...

SF-ROB-12343

These clear yellow precision disk wheels have an outer diameter of 2”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are...

SF-ROB-12342

These servo gears are made specifically to fit a Hitec C1 servo spline, allowing you to mate other gears to your servo. They have 24 teeth with a g...

SF-ROB-12341

These 1.375" long stainless steel D-Shafts have a diameter of ¼". The flat edge that runs the length of the shaft makes it an ideal drive shaft, wh...

SF-ROB-12340

The Qwiic Visible Spectral Sensor uses the AS7262 visible spectrometer from AMS for spectral identification. What can you do with Reflectance Spect...

SF-SPX-14290

These 3" long stainless steel shafts have a diameter of 1/8". These shafts are solid, which makes them an ideal choice for axles. These shafts have...

SF-ROB-12339

This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. The swtiches on each bo...

SF-DEV-09350

These 6" long stainless steel shafts have a diameter of 3/16". These shafts are solid, which makes them an ideal choice for axles. These shafts hav...

SF-ROB-12338

These 6" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". When used with the mat...

SF-ROB-12337

These smooth (round) belts have a Durometer hardness of A70 and can withstand temperatures from -35 to 250 degrees F. Their elastic nature allows t...

SF-ROB-12336

These 10" long stainless steel shafts have a diameter of 3/16". These shafts are solid, which makes them an ideal choice for axles. These shafts ha...

SF-ROB-12335

This is not your normal PIR! The Qwiic Human Presence Sensor - AK9750 is a passive infrared sensor with four discrete sensors built into one digita...

SF-SPX-14289

Here, for all your mechatronic needs, is a simple, high quality continuous continuous rotation servo motor. This servo is able to take in 6 volts a...

SF-ROB-09347

These blue precision disk wheels have an outer diameter of 3”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are ideal f...

SF-ROB-12334

Pillow block bearing mounts attach to the outside of a channel and can be used as simple hinges. These bearing mounts have a width of 1.32”, a thic...

SF-ROB-12333

These zinc-plated socket head machine screws are 5/8” long and have a tread pitch of 6-32. Sold in packs of 25. Note: These screws require a 7/64"...

SF-ROB-12332

This servo plate allows you to attach gears and mechanical structures to your standard sized servo. There are 4 6-32 tapped holes for mounting your...

SF-ROB-12330