SparkFun Australia

The SparkFun RFID USB Reader is a simple to use, USB to serial base unit for the ID-3LA, ID-12LA, and ID-20LA readers. Simply plug a reader into th...

SF-SEN-09963

This module from Roving Networks is powerful, small, and very easy to use. This Bluetooth module is designed to replace serial cables. The Bluetoot...

SF-WRL-12575

This is the RN-42 module from Roving Networks, a powerful, small, and very easy to use. This Bluetooth module is designed to replace serial cables....

SF-WRL-12574

This is the XBee WiFi Module with wire antenna from Digi. XBee WiFi embedded RF modules provide simple serial to IEEE 802.11 connectivity. By bridg...

SF-WRL-12571

These 10 segment bar graph LEDs have many uses. With a compact footprint, simple hookup, they are easy for prototyping or finished products. Essent...

SF-COM-09937

These 10 segment bar graph LEDs have many uses. With a compact footprint, simple hookup, they are easy for prototyping or finished products. Essent...

SF-COM-09936

This tiny little guy is the ALS-PT19, an SMD ambient light sensor that is much smaller than the standard TEMT6000. The ALS-PT19 is capable of takin...

SF-SEN-12566

Channel sliders let you achieve precise linear motion with Actobotics channels. The G type channel sliders enclose the bottom of a channel leaving ...

SF-ROB-12565

Channel sliders let you achieve precise linear motion with Actobotics channels. The F type channel sliders enclose the a side of a channel leaving ...

SF-ROB-12564

Channel sliders let you achieve precise linear motion with Actobotics channels. The E type channel sliders enclose the open top of a channel leavin...

SF-ROB-12563

This is a simple two wire cable. It has bare wires on both ends with a Molex A and B connector in the middle. With thicker 18 AWG wire, it’s better...

SF-PRT-09923

Channel sliders let you achieve precise linear motion with Actobotics channels. The D type channel sliders enclose one side and the open top of a c...

SF-ROB-12562

Channel sliders let you achieve precise linear motion with Actobotics channels. The C type channel sliders enclose the right, left, and closed bott...

SF-ROB-12561

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin Molex connector with 0.1" spac...

SF-PRT-09918

Channel sliders let you achieve precise linear motion with Actobotics channels. The A type channel sliders fully enclose the channel more rigid lin...

SF-ROB-12559

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST connector on one end, bar...

SF-PRT-09916

These aluminum beams are great for making unique links and connections in your Actobotics project thanks to 21 through-holes running its length and...

SF-ROB-12558

OBDII is an on board diagnostics standard that is used on a large variety of cars. OBD-II provides access to numerous data from the engine control ...

SF-DEV-09911

The surface mount plate make it easy to mount pillow blocks, hub mounts, or other Actobotics products to flat surfaces like workbenches, or wooden ...

SF-ROB-12557

A very powerful 5mW green laser. Fun, but don’t point in anyone’s eyes. These units include two solder points for permanent on. The trim-pot adjust...

SF-COM-09906

These blue “skate” wheels have an outer diameter of 4.90”, an inner diameter of 0.87”, and a width of 0.94”. When used in conjunction with the skat...

SF-ROB-12556

LinkM is a USB adapter that addresses two of the most frequently-requested BlinkM features. It enables you to program BlinkMs without setting up a ...

SF-COM-09903

These 2.75" long stainless steel D-Shafts have a diameter of ¼". The flat edge that runs the length of the shaft makes it an ideal drive shaft, whe...

SF-ROB-12555