SparkFun Australia

This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. If anything moves after...

SF-SEN-13285

MOSFETs are awesome. They’re like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy to switch a battery su...

SF-PRT-11214

We know you love adding color to your e-textiles, adding the LilyPad Pixel Board to your project will only make it better. The pixel board is compa...

SF-DEV-13264

This is a standard 3.5mm stereo jack with no frills. Panel mount in a 6mm diameter hole for a nice clean headphone, microphone or serial data conne...

SF-COM-11154

This through-hole speaker is great for projects where you need something that sounds better than a piezo buzzer but don’t have room for a full-blow...

SF-COM-11089

This is the same 18650 Lithium Ion Cell that you know and love, but now includes pre-attached solder tabs! These round high capacity cells have bee...

SF-PRT-13189

These motorized sliders are very cool. Each is essentially a standard slide pot which is belt-driven by a small motor. The slide contains two separ...

SF-COM-10976

Surface transducers give you the awesome power to turn almost any surface into a speaker. They’re essentially just a speaker except instead of a co...

SF-COM-10975

The SparkFun Servo Trigger is a small robotics board that simplifies the control of hobby RC servo motors. When an external switch or logic signal ...

SF-WIG-13118

This little piece of notched plastic is a Resistor Lead Bending Tool. Sometimes referred to as a “forming” tool, this little guy provides you with ...

SF-TOL-13114

These are 155mm long jumpers terminated as male to male. Use these to jumper from any female header on any board, to any other female header. Multi...

SF-PRT-10897

This is a 12 wire slip ring, a remarkably simple electromechanical assembly that allows electronic signals to be passed through its rotating innard...

SF-ROB-13065

This ANT500 is a telescopic antenna designed for operation from 75 MHz to 1 GHz with a total length that is configurable from 20 cm to 88 cm long. ...

SF-WRL-13002

Integrating Ethernet support into your project is a great way to relay data through a local area network and even bounce information out to the int...

SF-CAB-10759

Ribbon cable is really helpful in situations where you need to make a lot of connections without a big mess of wires. Nothing makes a project look ...

SF-CAB-10647

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features: 620-625nm Red 1...

SF-COM-10632

This is a small device called a reed switch. When the device is exposed to a magnetic field, the two ferrous materials inside the switch pull toget...

SF-COM-10601

This is an incredibly simple two cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fa...

SF-PRT-12900

These wireless transmitters work with our 315MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a v...

SF-WRL-10535

XBee radios are an awesome way to add wireless capability to your Arduino project and now it’s even easier with the SparkFun XBee Shield. The shiel...

SF-WRL-12847

The ADXL337 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned analog voltage outputs that measures acceleration wi...

SF-SEN-12786

This AT407 basic tilt switch can easily be used to detect orientation. Inside the can is a ball that make contact with the pins when the case is up...

SF-SEN-10289

We don’t want to hype this solder TOO much, but this could possibly be the best solder in the world. There, we’ve said it. This is a special blend ...

SF-TOL-10242

USB 2.0 type A to micro USB 5-pin. This is a new, smaller connector for USB devices. Micro USB connectors are about half the height of mini USB. Mi...

SF-CAB-10215