SparkFun Australia

This is a simple LED-illuminated tactile button with a green cap. It’s just like a basic tactile button, but it lights up green! So now you can get...

SF-COM-10440

The Panavise Jr. is a great vise with a vacuum base. Its jaws open up to about 3" and have grooves for PCBs. It’s perfect for light duty field repa...

SF-TOL-10410

These are 6" long jumper wires with male connectors on both ends. Use these to jumper from any female header on any board, to any other female head...

SF-PRT-12795

This is the SparkFun “Time-of-Flight” Range Finder, a breakout for the VL6180 distance sensor. Unlike most distance sensors that rely reflected lig...

SF-SEN-12784

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends...

SF-PRT-10370

The SparkFun Logomatic v2 takes everything we learned with logging analog or serial data from your projects over the years and boils it down to an ...

SF-WIG-12772

This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. We...

SF-ROB-10335

This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knoc...

SF-BOB-12758

If you use your hobby knife a lot, chances are you will need extra blades. These #11 blades are very sharp and good for trimming all sorts of thing...

SF-TOL-10325

This breakout board makes it easy to use the tiny MMA8452Q accelerometer in your project. The MMA8452Q is a smart low-power, three-axis, capacitive...

SF-SEN-12756

This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales (you know, the ones you use in January for your...

SF-SEN-10245

The eTape Liquid Level Sensor from Milone Technologies is a great way to measure the level of a liquid. It has a resistive output that varies with ...

SF-SEN-10221

This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins ...

SF-PRT-12699

The SparkFun MP3 Player Shield is an awesome MP3 decoder with the capabilities of storing music files onto a run-of-the-mill microSD card, thus giv...

SF-DEV-12660

This is essentially a ramped up version of our Ardumoto motor driver shield. For this SparkFun Monster Moto Shield we’ve replaced the L298 H-bridge...

SF-DEV-10182

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features: 600-610nm Orange ...

SF-COM-12645

The SparkFun Sound Detector is a small and very easy to use audio sensing board with three different outputs. The Sound Detector not only provides ...

SF-SEN-12642

RTC stands for real time clock folks. The DS3234 is a low-cost, extremely accurate SPI bus RTC with an integrated temperature compensated crystal o...

SF-COM-10079

We have no idea what USB device you are hooking up to, but if you want to access the microUSB port on something, you might want this. We broke out ...

SF-BOB-10031

Knobs are a great way to finish off your project and make it easier to adjust the level of your death ray. This knob mates to a 0.25" shaft. The kn...

SF-COM-10002

The Bluetooth Mate Gold is very similar to our BlueSMiRF modem, but it is designed specifically to be used with our Arduino Pros and LilyPad Arduin...

SF-WRL-12580

This new version now has all 5 pins broken out on the connector. We have no idea what USB device you are hooking up to, but if you need to add a mi...

SF-BOB-09966

This new version corrects the pin out for the GPX and RESET pins. The SparkFun USB Host Shield contains all of the digital logic and analog circuit...

SF-DEV-09947

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin Molex connector with 0.1" spac...

SF-PRT-09922

We all know that you can never get too many LEDs. Don’t worry, we’ve got you covered. This is a mixed pack of 26 LEDs all conveniently packaged in ...

SF-COM-09881

We all know that you can never get too many LEDs. Don’t worry, we’ve got you covered. This is a pack of 25 LEDs all conveniently packaged in a nice...

SF-COM-09850

Aavid Thermalloy Theragrip is a double sided tape for ceramic or metal heatsink packages. Theragrip provides both good thermal performance and exce...

SF-PRT-09771

This is a 2-pin, through-hole PH series JST connector. The pins are spaced by 2mm. We really like the solid locking feeling and high current rati...

SF-PRT-09749

The ScrewShield extends all pins of the Arduino out to 3.5mm pitch screw terminals. It also has a lot of the utility provided by Arduino Protoshiel...

SF-DEV-09729

The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The VCC pins of this...

SF-DEV-09717

This is a small prototyping shield for the Arduino Pro Mini. If your project requires just a little bit more space for your external circuitry, thi...

SF-DEV-09709

These 3" long stainless steel shafts have a diameter of ¼". These shafts are solid, which makes them an ideal choice for axles. These shafts have a...

SF-ROB-12478

This is a 5g syringe of white heatsink compound (aka thermal grease, thermal paste, thermal goo). Use this whenever you’re connecting a component t...

SF-PRT-09599