SparkFun Australia

This is the PICAXE-14M2 microcontroller chip. PICAXE is a neat entry-level microcontroller system that is relatively cheap to get started with. T...

SF-COM-10802

This is a simple 2x3 female PTH header. This header is in the common configuration for an ISP connector. Each pin has a spacing of 0.1" in between ...

SF-PRT-13010

Who doesn’t love the soft glow of electroluminescence? This EL tape is a flexible plastic ribbon which contains a phosphor layer and lights up with...

SF-COM-10793

The TRS (tip ring sleeve) jack breakout is a simple board that allows a ¼" stereo audio jack to be soldered on to gain easy access to all of its br...

SF-BOB-13005

This right-angle tactile switch has a great ‘click’ to it. Also, because it’s a through-hole design it’s very sturdy. Mount it on the edge of your ...

SF-COM-10791

This 200 pulse per rotation single-output encoder outputs electrical pulses which you can interpret using a microcontroller to find the position of...

SF-COM-10790

Metal short standoffs: 3/8" long x ¼"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development boards with available ho...

SF-PRT-10739

The NEMA 17 Stepper Motor Mount connects to the topside of a stepper motor to make integrating it into your Actobotics project even easier. Thanks ...

SF-ROB-12987

This is a 33 meter roll of polyimide tape. This tape is a fantastic insulator, like electrical tape, but it can withstand temperatures as high as 2...

SF-PRT-10687

With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/M...

SF-BOB-12941

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features: 465-470nm Blue ...

SF-COM-10635

EL wire, or electroluminescent wire, is a flexible wire coated in phosphor. Apply the appropriate voltage and it lights up! Each EL wire looks a lo...

SF-COM-12931

EL wire, or electroluminescent wire, is a flexible wire coated in phosphor. Apply the appropriate voltage and it lights up! Each EL wire looks a lo...

SF-COM-12930

EL wire, or electroluminescent wire, is a flexible wire coated in phosphor. Apply the appropriate voltage and it lights up! Each EL wire looks a lo...

SF-COM-12929

EL wire, or electroluminescent wire, is a flexible wire coated in phosphor. Apply the appropriate voltage and it lights up! Each EL wire looks a lo...

SF-COM-12925

The TLC5940 is a 16 channel PWM unit with 12 bit duty cycle control (0-4095), 6 bit current limit control (0-63), and a daisy chainable serial inte...

SF-BOB-10616

Sometimes when you have too many choices, it’s hard to make a good decision. In fact, there are times when you just want a bag of LEDs, just one of...

SF-COM-12903

If you’ve ever wondered how to control high current devices from a low-power microcontroller, a MOSFET is what you need. The NDP6020P is a very com...

SF-COM-12901

We all know that you can never get too many LEDs. Don’t worry, we’ve got you covered. This is a pack of 25 LEDs all conveniently packaged in a nice...

SF-COM-10557

This is a high quality switching ‘wall wart’ AC to DC 5V 2000mA Barrel Jack wall power supply manufactured specifically for SparkFun Electronics. T...

SF-TOL-12889

If you aren’t familiar with the Electric Imp, it essentially provides an easy, integrated way to connect almost any hardware device both to other d...

SF-DEV-12887

This is the latest version of our popular through-hole Simon Says Kit. We’ve made some changes to the board that should make it easier than ever fo...

SF-KIT-10547

These wireless transmitters work with our 434MHz receivers. They can easily fit into a breadboard and work well with microcontrollers to create a v...

SF-WRL-10534

We know this looks like a lot of our other LEDs, but it’s not! This is a PTH Addressable RGB LED with a WS2812 control IC built right into the LED....

SF-COM-12877

These wireless receivers work with our 434MHz transmitters. They can easily fit into a breadboard and work well with microcontrollers to create a v...

SF-WRL-10532

This is the Vernier Gas Pressure Sensor, an easy to operate tool that can be used to monitor pressure changes of a gaseous element. The range on th...

SF-SEN-12874

This 9V battery holder allows your battery to snap in tight and holds it in place, which is great in situations where you don’t want the battery ju...

SF-PRT-10512

Want to start playing with sensors, but don’t know where to begin? This kit includes a variety of basic sensors for any beginner or experienced pro...

SF-SEN-12862

These connectors are made from high-temp nylon with gold-plated spring pins or sockets molded in. The shape of this generic XT60 prevents reverse p...

SF-PRT-10474

EL inverters allow you to drive EL (electroluminescent) wires. This particular EL inverter accepts a 12 VDC wall adapter. The output is terminated ...

SF-COM-10469

This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. Note: Populate the board according...

SF-BOB-10467

The Beaglebone Black is a great credit-card-sized development platform with a fast growing community, why would you not want to keep your board saf...

SF-PRT-12842

We could talk about how the Zinc used in these nuts is only from the finest old-growth Zinc trees from across the globe and is hand picked only at ...

SF-PRT-10454

There are your standard Philips-head 4-40 screws. They are ¼" long and come in packs of ten. This is the screw size we use in most of the holes for...

SF-PRT-10453

Standard Philips-head 4-40 screws. They are ¾" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout b...

SF-PRT-10451

While our small diagonal cutters are great for hobby use, sometimes you need something with a little more bite. These electronic snippers are great...

SF-TOL-10447

This is the FadeCandy from Adafruit, a USB controlled LED driver with on-board dithering to help illuminate your Neopixel project. Even though the ...

SF-COM-12821

The ADXL377 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned analog voltage outputs that has a full-scale range ...

SF-SEN-12803

This board is an evaluation platform for the SM130 RFID module. It includes an XBee header, PCB trace antenna, and has the layout to be used as a s...

SF-DEV-10406

If you need to charge LiPo batteries, this simple charger will do just that. It is designed to charge single-cell Li-Ion or Li-Polymer batteries. C...

SF-PRT-10401

This is a 2x40 pin right-angle PTH header. This header can be broken apart with a fair amount of force to form smaller header formations. Don’t wor...

SF-COM-12792

This is a 2x23 pin female PTH header, with extra long legs which makes great for stacking. This piece is in the common configuration for Beaglebone...

SF-PRT-12790

This is the SparkFun RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring,...

SF-SEN-12787

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends...

SF-PRT-10375

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both end...

SF-PRT-10373

This is a simple six wire cable. Great for jumping from board to board or just about anything else. There is a 6-pin JST RE connector on both ends....

SF-PRT-10371

This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both end...

SF-PRT-10368

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST RE connector on both ends....

SF-PRT-10367