SparkFun Australia

Check out these big 10mm through-hole LEDs! The opaque epoxy package causes these LEDs to have a soft, diffuse glow. Features: 587-591nm Yellow...

SF-COM-10634

This is the SMD version of PRT-07948, which is the unit we like to use as RTC backup and SRAM backup for GPS units. Holds battery in place with fri...

SF-PRT-10592

Do you ever wish your Arduino was more musically talented? Or maybe your project could use some cool sound effects. The SparkFun Musical Instrument...

SF-DEV-10587

This is an incredibly simple one cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fa...

SF-PRT-12899

The SparkFun MIDI Shield board gives your Arduino-based device access to the antiquated, but still widely used and well supported MIDI communicatio...

SF-DEV-12898

What should every hacker have available to them? That’s right, a screwdriver (you have to get into those cases somehow). What makes screwdrivers ev...

SF-TOL-12891

This is a 2-pin JST RCY connector typically used for low-voltage applications running 10A or less. They are commonly found in RC vehicles. These co...

SF-PRT-10501

You don’t have the power? Well, there’s no need to ask Scotty – the SparkFun Benchtop Power Board Kit has your back. This board will let you take a...

SF-KIT-12867

This charger accurately balances and charges Lithium Polymer, LiFe (A123), NiCd and NiMH batteries. It will handle LiPo/LiFe up to 6S and NiMH/NiCd...

SF-PRT-10473

Note: This camera case does not currently fit the Raspberry Pi Camera Module V2. We are currently looking for a resolution to this issue. The Raspb...

SF-PRT-12846

Standard Philips-head 4-40 screws. They are ½" long and come in packs of ten. This is the screw size we use in most of the holes for our breakout b...

SF-PRT-10452

If you’ve had ideas for a project that depends on the ability to sense different spectrums of visible light and react based on those measurements, ...

SF-SEN-12829

This is a simple LED-illuminated tactile button with a green cap. It’s just like a basic tactile button, but it lights up green! So now you can get...

SF-COM-10440

The Panavise Jr. is a great vise with a vacuum base. Its jaws open up to about 3" and have grooves for PCBs. It’s perfect for light duty field repa...

SF-TOL-10410

These are 6" long jumper wires with male connectors on both ends. Use these to jumper from any female header on any board, to any other female head...

SF-PRT-12795

This is the SparkFun “Time-of-Flight” Range Finder, a breakout for the VL6180 distance sensor. Unlike most distance sensors that rely reflected lig...

SF-SEN-12784

This is a simple five wire cable. Great for jumping from board to board or just about anything else. There is a 5-pin JST RE connector on both ends...

SF-PRT-10370

The SparkFun Logomatic v2 takes everything we learned with logging analog or serial data from your projects over the years and boils it down to an ...

SF-WIG-12772

This pan/tilt bracket consists of two brackets and all the hardware you need to attach them to make a pan/tilt mechanism using two servo motors. We...

SF-ROB-10335

This small breakout board couples an Electret microphone (100Hz–10kHz) with a 60x mic preamplifier to amplify the sounds of voice, claps, door knoc...

SF-BOB-12758

If you use your hobby knife a lot, chances are you will need extra blades. These #11 blades are very sharp and good for trimming all sorts of thing...

SF-TOL-10325

This breakout board makes it easy to use the tiny MMA8452Q accelerometer in your project. The MMA8452Q is a smart low-power, three-axis, capacitive...

SF-SEN-12756

This load sensor, sometimes called a strain gauge, is the same one found in digital bathroom scales (you know, the ones you use in January for your...

SF-SEN-10245