SparkFun Australia

This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on on...

SF-CAB-12970

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we’re always up to date...

SF-TOL-10603

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we’re always up to date...

SF-TOL-10602

This is the Mini SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our mini modular breadboards with the same connections to pi...

SF-PRT-12702

The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical ...

SF-SEN-12650

There are more and more hobbyists taking advantage of surface mount technology these days. With affordable tools like hot air and hotplate reflow o...

SF-PRT-12621

The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this...

SF-DEV-09718

Is your I2C bus not ACK'ing the way you expect? Do you need to discover a UART's mysterious baud rate? Or do you want to reverse engineer an SPI pr...

SF-TOL-18627

The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network...

SF-WRL-17146

This 2x20 pin female header is meant to allow you to extend the reach of any board with the standard 2x20 GPIO pin footprint like the Raspberry Pi,...

SF-PRT-16763

The SparkFun micro:climate kit is a full weather station kit that is built on top of the weather:bit carrier board. Unlike previous weather kits we...

SF-KIT-16274

The SparkFun Qwiic Scale is a small breakout board for the NAU7802 that allows you to easily read load cells to accurately measure the weight of an...

SF-SEN-15242

These are your run-of-the-mill ¼ Watt, +/- 5% tolerance PTH resistors. Commonly used in breadboards and other prototyping applications, these 100 o...

SF-PRT-14493

This is an easy-to-assemble pan/tilt bracket kit that utilizes servos to move on two axes fit for camera and helping-hand applications. This partic...

SF-ROB-14391

This Digital LED Voltmeter measures the voltage at a particular point of the system it has been hooked up to and then provides a readout on its thr...

SF-PRT-14313

This is a solderer’s best helper, the third hand. Comes with a heavy base, two alligator clips, a soldering iron holder, and a good magnifying glas...

SF-TOL-09317

Whether you’re an agriculturalist, a professional meteorologist or a weather hobbyist, building your own weather station can be a really rewarding ...

SF-SEN-08942

Ever wanted to play with those newfangled RFID tags? Although it’s been around for a while, the technology has been extremely cost-prohibitive and ...

SF-WRL-14147

This is your solution when you absolutely, positively need to get the most out of an antenna for your next RFID project. This ultra high-frequency ...

SF-WRL-14131

Miniature surface mount momentary button. These are great, low-profile momentary switches. Perfect as a tactile reset switch. Rated up to 50mA. D...

SF-COM-08720

Basic breakout board for the TEMT6000 Ambient Light Sensor. Only what you need, nothing you don’t. Sensor acts like a transistor - the greater the ...

SF-BOB-08688

These needle tipped multimeter probes are great for attaching to multimeters, power supplies, oscilloscopes, function generators, etc. Not only can...

SF-TOL-12078

This is the SparkFun Solderable Breadboard. A bare PCB that is the exact size as our regular breadboard with the same connections to pins and power...

SF-PRT-12070

This is a simple pack of five Green LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew int...

SF-DEV-14011

This simple board breaks out a micro-B USB connector’s VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to add the popular micro-B ...

SF-BOB-12035

This is a 10-pin socket with 2mm pitch that mates with the popular XBee radio from Digi. Use this small part to avoid having to solder your preciou...

SF-PRT-08272

Dip sockets for all your prototyping needs. If you’ve ever had to de-solder a dip part from a circuit board, you know how valuable these are! Numbe...

SF-PRT-07942

The LIS3DH Breakout is a smart, low-power, three-axis, capacitive micro-machined accelerometer with 12 bits of resolution that you can use to add t...

SF-SEN-13963

Single row of 30-holes, female header with swiss round machined pins. These units have very high quality round pins to accept and retain machine pi...

SF-PRT-00743

Need range? 2.4GHz Large Duck Antenna 5dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. ...

SF-WRL-00558

Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making...

SF-PRT-13827

2.4GHz Duck Antenna 2.2dBi with Reverse Polarized - SMA RF connector. Perfect for prototyping with our RF ICs. 50 ohm impedance. 4" long.The FCC is...

SF-WRL-00145

The Due is Arduino’s first ARM-based Arduino development board. This board is based on a powerful 32bit CortexM3 ARM microcontroller made programma...

SF-DEV-11589

We’ve all seen toys and things that change color when you run them under warm water or heat them up in the sun. Some of us were especially mesmeriz...

SF-COM-11555

The SN74HC595N is a simple 8-bit shift register IC. Simply put, this shift register is a device that allows additional inputs or outputs to be adde...

SF-COM-13699

The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network...

SF-WRL-13678