SparkFun Australia

These standard gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost anything else that needs to ...

SF-ROB-12532

This is a 5mm PTH fuse clip intended to be used with our Glass Fuses. Note: These are sold in single units. If you intend to secure a fuse using t...

SF-COM-09773

This is a glass ferrule type fuse. It fits great with our 5mm fuse clips. The fuse is rated for 125VAC, up to 5A. Fuses are pretty simple, if more ...

SF-COM-09772

These hub-mountable aluminum pulleys can be used to drive wheels or other pulleys with ¼” or ⅛” belts. They have an outer diameter of 1.125”, a bor...

SF-ROB-12523

The SparkFun Joystick Shield Kit contains all the parts you need to enable your Arduino with a joystick! The shield sits on top of your Arduino and...

SF-DEV-09760

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 10:1 and operate up to 12 volts and have a stal...

SF-ROB-12518

The swivel hub lets you connect any two parts with the 0.77" hub pattern together and have them swivel a full 360 degrees. Internal ball bearings a...

SF-ROB-12509

Now mounted on a breakout board, the MPL115A1 is a digital barometer that uses MEMs technology to give accurate pressure measurements between 50kPa...

SF-SEN-09721

These couplers allow you to connect a 1/4” shaft directly to your C1 Hitec servo spline. The set screw included with each shaft coupler works well ...

SF-ROB-12501

These aluminum channels are the building blocks to the Actobotics line and function as the back bone to your electromechanical project. These chann...

SF-ROB-12500

These aluminum channels are the building blocks to the Actobotics line and function as the back bone to your electromechanical project. These chann...

SF-ROB-12498

The Micro Maestro is the first of Pololu’s second-generation USB servo controllers. The board supports three control methods — USB for direct conne...

SF-ROB-09664

These stainless steel shaft couplers allow you to couple two size shafts together. They can be used for connecting motor shafts to drive shafts, or...

SF-ROB-12493

These shaft-mountable aluminum timing pulleys use XL timing belts and attach to a 6mm output shaft with a set screw. They have 10 teeth with a gear...

SF-ROB-12490

We all know that you can never get too many LEDs. Don’t worry, we’ve got you covered. This is a pack of 25 LEDs all conveniently packaged in a nice...

SF-COM-09661

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very standa...

SF-COM-09650

This is a super-high intensity Luxeon Rebel LED, warm white in color. These LEDs provide optimized light quality and efficiency to address a number...

SF-COM-09637

LEDs - those blinky things. A must have for power indication, pin status, opto-electronic sensors, and fun blinky displays. This is a very basic ...

SF-COM-09592

These clamping hubs are a great and cost-effective choice when attaching hub mount gears or wheels to shafts or tubes and can be a better option th...

SF-ROB-12455

The mbed microcontroller is an ARM processor, a comprehensive set of peripherals and a USB programming and communication interface provided in a sm...

SF-DEV-09564

This board allows you to interface with your car’s OBD-II bus. It provides you a serial interface using the ELM327 command set and supports all maj...

SF-WIG-09555

The QRE1113 is a small IR reflectance sensor. This sensor is often used in line following robots because, if it can sense if a surface is white or ...

SF-COM-09542

These red precision disk wheels have an outer diameter of 5”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are ideal fo...

SF-ROB-12435

This is a right-angle, 24-pin Molex Mini-Fit Jr.™ connector, commonly used as the power supply connector on ATX motherboards. Two rows of twelve pi...

SF-PRT-09498