SparkFun Australia

The SparkFun 5V/1A LiPo Charger/Booster is a no-nonsense circuit for generating one amp from a Lithium Polymer battery at 5V. This LiPo charger is ...

SF-PRT-14411

This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for mashing. This button...

SF-COM-09336

The SparkFun Sound Detector is a small and very easy-to-use audio sensing board with three different outputs. The Sound Detector not only provides ...

SF-SEN-14262

This is a very simple 1m long TNC to RP-SMA cable. We like to use this cable to connect our ultra high-frequency RFID antennas to an equally powerf...

SF-CAB-14132

This is a coin cell holder for the common CR2032 type battery. The holder has a neat pop-in, pop-out feature that makes changing the battery easy. ...

SF-DEV-08822

This is a very simple but extremely handy, 1" square, single sided perf board. Standard 0.1" spacing with a 4-40 (3mm) hole for mounting. Every thr...

SF-PRT-08808

A simple flex sensor 4.5" in length. As the sensor is flexed, the resistance across the sensor increases. Patented technology by Spectra Symbol - t...

SF-SEN-08606

This is the SparkFun RJ11 Breakout, two simple breakout boards for the common 6-pin RJ11 connector. These little boards can easily have one of our ...

SF-BOB-14021

This green Mini Breadboard is a great way to prototype your small projects! With 170 tie points there’s just enough room to build and test simple c...

SF-PRT-12046

Low profile 3.5mm stereo audio jack.Documents:Audio 3.5mm Jack Datasheet

SF-PRT-08032

Standard 22 AWG solid Red hook up wire. Use this with your bread board or any project in which you need sturdy wire. Comes in small spools of 25'.

SF-PRT-08023

The SparkFun Weather Shield is an easy-to-use Arduino shield that grants you access to barometric pressure, relative humidity, luminosity and tempe...

SF-DEV-13956

6 pin SOT-23 to DIP adaptor. Created to take SOT23 of various pin sizes breakout to DIP. This will work with 3-pin MOSFETs, BJTs, Voltage Regulator...

SF-BOB-00717

This is a standard issue USB 2.0 cable. This is the most common A to B Male/Male type peripheral cable, the kind that’s usually used for printers. ...

SF-CAB-00512

Copper tape has countless applications in electronics from creating low-profile traces for electrical components to RF-shielding and antenna-making...

SF-PRT-13828

The Tsunami Super WAV Trigger is the next evolutionary step beyond the original WAV Trigger. Based on a new generation ARM Cortex m7, the Tsunami ...

SF-WIG-13810

An oscilloscope is an awesome tool to have around the shop. Unfortunately, most scopes take up quite a bit of bench space and they’re not very port...

SF-TOL-11702

Cherry MX Keyswitches are top-of-the-line mechanical keyboard switches. They’re satisfyingly “clicky”, reliable up to tens-of-millions of key press...

SF-BOB-13773

4-digit 7-segment displays are really neat little devices, it’s a shame that they can be so cumbersome to control. Well we’ve solved that problem b...

SF-COM-11629

A simple slide potentiometer can go a long way. Rated at 10KOhm and 0.1W. Comes with solder tab connections. The pot has an overall travel of 20mm ...

SF-COM-11620

This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with off...

SF-DEV-13746

We’ve all seen toys and things that change color when you run them under warm water or heat them up in the sun. Some of us were especially mesmeriz...

SF-COM-11558

4-digit 7-segment displays are really neat little devices, it’s a shame that they can be so cumbersome to control. Well we’ve solved that problem b...

SF-COM-11442

The LilyTwinkle is a tiny little LilyPad board designed to add some twinkle to your project. Even though it’s as small as some of the LilyPad senso...

SF-DEV-11364

This simple on-off switch is rated for 20A at 12V but who cares about all that, it looks way awesome. These toggle switches come with those missile...

SF-COM-11310

This is a 1.5' long USB extension cable equipped with type A male connector on one end to plug into your computer and a type A female connector at ...

SF-CAB-13309

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the ...

SF-COM-11288

The Arduino Ethernet Shield 2 allows an Arduino Board to connect to the Internet. It is based on the Wiznet W5500 Ethernet chip. The Wiznet W5500 p...

SF-DEV-11166

This is the Circuit Scribe Conductive Ink Pen, a simple looking ball-point pen that allows you to draw circuits instead of soldering or wiring them...

SF-COM-13254

This is the Magnetic Door Switch Set, a small reed switch assembly specifically designed to alert you when doors, drawers, or any other aperture op...

SF-COM-13247

This is a USB 2.0 type A to Micro-B 5-pin black cable. You know, the mini-B connector that usually comes with cell phones, Cameras, MP3 players, et...

SF-CAB-13244

The Solder Vacuum, a great (and sometimes under appreciated) little tool for solder rework. It allows you to pull the molten solder out of a connec...

SF-TOL-13203

These crimping pliers allow you to easily make your own wiring harnesses using crimp pins and cable housings. We really like the quality and sturdi...

SF-TOL-13193

Bare Conductive’s Electric Paint is just like any other water-based paint… except that it’s electrically conductive! This means that you can actual...

SF-COM-10994

PICAXE-08M2 microcontroller chip. PICAXE is a neat entry-level microcontroller system that is relatively cheap to get started with. The chip is p...

SF-COM-10803

This is the HackRF One, a Software Defined Radio (SDR) peripheral capable of transmission or reception of radio signals from 1MHz to 6GHz. Designed...

SF-WRL-13001

Alligator clips (or Crocodile clips, if you prefer) are likely to be the most useful thing on your workbench besides the workbench itself. Whether ...

SF-PRT-12978

This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST RE connector on both ends...

SF-PRT-10374

These plastic Flexible Coolant Pipes have been primarily used to spray refrigeration or washing fluid for machine tools but, thanks to their articu...

SF-TOL-12783

This simple board breaks out a female USB type A connector’s VCC, GND, D- and D+ pins to a 0.1" pitch header. If you want to add a USB to  your pro...

SF-BOB-12700

The Nokia 5110 is a basic graphic LCD screen for lots of applications. It was originally intended to be used as a cell phone screen. This one is mo...

SF-LCD-10168

This is a 10-pin header with 2mm pitch that mates with our XBee socket. It can be used for making ‘dummy XBees’ or anything else you want! Note: T...

SF-PRT-10112

This is a simple two wire cable. Great for jumping from board to board or just about anything else. There is a 2-pin JST connector on one end, bare...

SF-PRT-09914

The new version of the UBW32 now uses the PIC32MX795 IC. Based on the work of Brian Schmalz, the UBW32 is a small development board for the new PIC...

SF-DEV-09713

This simple cable has so many uses! Plug the 9 volt battery clip onto a standard 9V battery and connect the other end to anything with a 5.5x2.1mm,...

SF-PRT-09518

We love heat shrink! We use it for all sorts of handy projects. Use it to reinforce connections, protect devices, and electrically isolate exposed ...

SF-PRT-09353

The Raspberry Pi Pico W builds upon the great cost-for-performance metrics of the Pico and add WiFi to the board. The Pico W features the same attr...

SF-DEV-20174