SparkFun Australia

Under-powering a digital device can sometimes have pretty nasty consequences. Brown-out conditions can cause memory to get written or overwritten i...

SF-KIT-11087

The FabFM is a stylish FM radio kit that you can build with just basic soldering tools! The PCB is all PTH, meaning that even a beginner solderer c...

SF-KIT-11043

Your 5 volt system can wield great power with this big beefy relay board. How does 20 amps at 220VAC sound? The SparkFun Beefcake Relay Control Ki...

SF-KIT-11042

This is the latest version of the Simon SMD soldering kit, the surface mount version of our popular Simon Kit. It’s considered an intermediate kit ...

SF-KIT-10935

Infrared LEDs are awesome. Along with an IR receiver they can be used for remote control and even basic remote data communication. The only problem...

SF-KIT-10732

A solid state relay (SSR) is just what it sounds like; an IC that acts like a mechanical relay. They allow you to control high-voltage AC loads fro...

SF-KIT-10684

This kit was designed to accompany Rob Faludi’s Building Wireless Sensor Networks book, which is the comprehensive guide to ZigBee wireless networ...

SF-KIT-10413

Botanicalls Kits let plants reach out for human help! They offer a connection to your leafy pal via online Twitter status updates to your mobile ph...

SF-KIT-10334

This is the new revision of the kit. We switched to a better trimpot and green LED. This is a kit that gives you all of the basic thru-hole compone...

SF-KIT-10003

This is a kit for a 3x3x3 cube of RGB LEDs. This kit contains everything you’ll need - 27 LEDs, an ATmega328 microcontroller, a custom PCB, and oth...

SF-KIT-09867

The original Cylons are from TV’s Battlestar Galactica. They are humanoid robots with a scanning red visor where their eyes should be. This is a ...

SF-KIT-09286

The SparkFun Metro-Gnome is a basic digital metronome used to keep time during music practice. This is a basic kit that goes together in 15-20 minu...

SF-KIT-09236

This is SparkFun Terror-Min, the wonderful toy to annoy and bring terror to the most patient parents. It’s a simple kit based on the principals of ...

SF-KIT-09206

This is a large mass of items that go along with the Beginning Embedded Electronics lectures. You will get all the following parts in a kit to go a...

SF-KIT-08373

This is the new UAV Development Board v3 (aka, UDB3). The UDB3 board comes with a dsPIC30F4011 CPU, an MMA7260 three axis accelerometer, and two du...

SF-GPS-09980

This is the RFduino Dual AAA Battery Shield, a long add-on board for the RFduino DIP module that supplies 3.3V to your whole project. This shield c...

SF-DEV-13214

This is the RFduino Proto Shield, a finger-tip sized board that can be attached to the main RFduino Dip module to create your own custom circuits a...

SF-DEV-13213

This is the RFduino Servo Shield, a small board that can be used with the RFduino DIP module to drive up to 4 servos at once. This pretty much as s...

SF-DEV-13211

The Intel® Galileo Gen 2 board is based on the Intel® Quark SoC X1000, a 32-bit Intel Pentium®-class system on a chip (SoC). It is the first board ...

SF-DEV-13096

The CryptoCape is the BeagleBone’s first dedicated security daughterboard and was made in collaboration with our Hacker In Residence, Josh Datko. K...

SF-DEV-12773

At SparkFun we use many Arduinos and we’re always looking for the simplest, most stable one. Each board is a bit different and no one board has eve...

SF-DEV-12757

This is a shield for the CC3000 WiFi Module. The CC3000 from TI (Texas Instruments) is a self-contained wireless network processor that makes incor...

SF-DEV-12071

The SparkFun Danger Shield mounts on top of your Arduino or Arduino Pro and equips it with a variety of fun and useful inputs and outputs. The Dang...

SF-DEV-11649

When you think about a piece of equipment like a mixed signal oscilloscope you usually think of, well, a piece of equipment. What you probably don’...

SF-DEV-11643

The Netduino Plus is an open source electronics platform using the .NET Micro Framework. The board features a 32-bit microcontroller and a rich dev...

SF-DEV-11608

You hear it all the time in the Arduino community, “will this shield work with my other shield?.” I think we’ve all been disappointed to find that ...

SF-DEV-11002

If you’re looking for a simple way to add a battery to your LilyPad project, the LilyPad Coin Cell Battery Holder might do the trick. It’s a simple...

SF-DEV-10730