SparkFun Australia

The TB6612FNG Motor Driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be u...

SF-ROB-14451

The SparkFun Qwiic Adapter provides the perfect means to make any old I2C board into a Qwiic-enabled board. This adapter breaks out the I2C pi...

SF-DEV-14495

This is your basic spool of leaded solder with a 63/37 water soluble resin core. 0.031" gauge and 100 grams. This is a good spool for more advanced...

SF-TOL-09161

This is a joystick very similar to the ‘analog’ joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers -...

SF-COM-09032

The SparkFun Simultaneous RFID Reader is an Arduino-compatible board to get you started with the M6E Nano UHF RFID Reader. Radio Frequency Identifi...

SF-SEN-14066

This is a simple to use, USB to serial base unit for the Digi XBee line. This unit works with all XBee modules including the Series 1 and Series 2....

SF-WRL-11812

This is a clever little breakout board for both the RGB and R/G illuminated rotary encoders. On one side, it breaks out all of the RGB pins to stan...

SF-BOB-11722

Simple SPDT slide switch. Rated at 30V/200mA. The pins have .1" spacing - fits great into a breadboard! Use it as a power switch or general control...

SF-COM-00102

We use these little buttons on everything! These Miniature Single Pole Single Throw switches have a good click to them and are breadboard friendly....

SF-COM-00097

These are a pair of basic, 65mm wheels with black rubber tires. These wheels are the same ones designed to fit onto DAGUs right angle gear motors u...

SF-ROB-13259

This is a USB 2.0 type B to Mini-B 5-pin black cable. You know, the mini-B connector that usually comes with USB Hubs, Cameras, MP3 players, etc. W...

SF-CAB-13243

This DC power jack/connector is just like the other one that we carry except that it’s terminated with breadboard-friendly pins instead of wide sol...

SF-PRT-10811

This is your simple three conductor sensor cable with electrode pad leads. These cables are 24" long and feature a 3.5mm audio jack connector on on...

SF-CAB-12970

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we’re always up to date...

SF-TOL-10603

You can tell by our large assortment of tweezers that we here at SparkFun are way into picking up tiny things. To make sure we’re always up to date...

SF-TOL-10602

This is the Mini SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our mini modular breadboards with the same connections to pi...

SF-PRT-12702

The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical ...

SF-SEN-12650

There are more and more hobbyists taking advantage of surface mount technology these days. With affordable tools like hot air and hotplate reflow o...

SF-PRT-12621

The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this...

SF-DEV-09718

Is your I2C bus not ACK'ing the way you expect? Do you need to discover a UART's mysterious baud rate? Or do you want to reverse engineer an SPI pr...

SF-TOL-18627

The ESP8266 WiFi Module is a self contained SOC with integrated TCP/IP protocol stack that can give any microcontroller access to your WiFi network...

SF-WRL-17146

This 2x20 pin female header is meant to allow you to extend the reach of any board with the standard 2x20 GPIO pin footprint like the Raspberry Pi,...

SF-PRT-16763

The SparkFun micro:climate kit is a full weather station kit that is built on top of the weather:bit carrier board. Unlike previous weather kits we...

SF-KIT-16274

The SparkFun Qwiic Scale is a small breakout board for the NAU7802 that allows you to easily read load cells to accurately measure the weight of an...

SF-SEN-15242