SparkFun Australia

These Adam Tech Wall Adapter Cables are terminated with a standard North American (NEMA 5–15P) plug at one end and three insulated spade terminal c...

SF-CAB-14092

These standard gearmotors are incredibly tough and feature full metal gears to help you drive wheels, gears, or almost anything else that needs to ...

SF-ROB-12144

The Electrically Isolated USB EZO™ Carrier Board allows you to connect your Atlas Scientific circuit directly to your computer or Raspberry Pi. Bui...

SF-SEN-14091

These micro gearmotors are incredibly tough and feature full metal gears. They have a gear ratio of 250:1 and operate up to 12 volts and have a sta...

SF-ROB-12143

The SIS-2 monitors an IR receiver, and when a certain remote code is detected, an output pin will toggle. Two outputs are available and any code on...

SF-SEN-08753

This is the ORP Kit, a large sensor kit that measures the ability of a solution to act as an oxidizing or reducing agent. Inside the kit you will f...

SF-SEN-14090

These servo gears are made specifically to fit a Hitec C1 servo spline, allowing you to mate other gears to your servo. They have 20 teeth with a g...

SF-ROB-12142

These 12" long stainless steel shafts have a diameter of 3/8". These shafts are solid, which makes them an ideal choice for axles. These shafts hav...

SF-ROB-12141

Flip-Pins are a fantastic new way to add headers to your breakout board. Designed by Fliptronics, Flip-Pins are the third generation of the Integra...

SF-COM-14087

These pinion gears attach to a 6mm D-shaft or gear motor using a setscrew. These gears have 32 teeth with a gear pitch of 32P, an outer diameter of...

SF-ROB-12140

These gray “skate” wheels have an outer diameter of 2.975”, an inner diameter of 0.87”, and a width of 0.94”. When used in conjunction with the ska...

SF-ROB-12139

Flip-Pins are a fantastic new way to add headers to your breakout board. Designed by Fliptronics, Flip-Pins are the third generation of the Integra...

SF-COM-14086

These single channel 45 degree angle brackets mate directly to Actobotics channels and hub mounts and are useful as attachment points. They share t...

SF-ROB-12138

This is the very popular 2.4GHz XBee XBP24-AWI-001 module from Digi. The Pro series have the same pinout and command set of the basic series with a...

SF-WRL-08742

Stay warm, outdoors! High quality hoodie with front pocket. Large logo on the front, blank back. If you’re shopping for the quintessential Americ...

SF-SWG-08741

These 7" long stainless steel D-Shafts have a diameter of ¼". The flat edge that runs the length of the shaft makes it an ideal drive shaft, when u...

SF-ROB-12137

Flip-Pins are a fantastic new way to add headers to your breakout board. Designed by Fliptronics, Flip-Pins are the third generation of the Integra...

SF-COM-14085

These stainless steel shaft couplers allow you to couple two size shafts together. They can be used for connecting motor shafts to drive shafts, or...

SF-ROB-12136

Two pin JST connector to a 2.1x 5.5mm barrel jack, 6.25 inch long jumper cable. We use this cable to adapt from a wall power supply to a relatively...

SF-TOL-08734

These 5" long stainless steel shafts have a diameter of 3/16". These shafts are solid, which makes them an ideal choice for axles. These shafts hav...

SF-ROB-12135

These blue precision disk wheels have an outer diameter of 5”, a width of 0.23”, and utilize the 0.77” hub pattern. These simple wheels are ideal f...

SF-ROB-12134

The STEMTera is an innovation in breadboard history. It is the first breadboard with an Arduino-compatible hardware suite built in that works with ...

SF-DEV-14083

Do not look into the light. You know you want to, but boy will you be sorry. 1W per channel, RGB High Power LEDs in one aluminum backed package. Th...

SF-COM-08718

Screw plates make it easy to create a strong joining point between our channel pieces. The ‘large’ screw plate is 1.3" square, has four 6-32 tapped...

SF-ROB-12133

These 2" long stainless steel shafts have a diameter of 3/8". These shafts are solid, which makes them an ideal choice for axles. These shafts have...

SF-ROB-12131

The STEMTera is an innovation in breadboard history. It is the first breadboard with an Arduino-compatible hardware suite built in that works with ...

SF-DEV-14082

These smooth (round) belts have a Durometer hardness of A70 and can withstand temperatures from -35 to 250 degrees F. Their elastic nature allows t...

SF-ROB-12130

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor’s resistance. Pressing lightly, the resistance chang...

SF-SEN-08713

This hub adapter lets you connect Actobotics parts with a 1.5" hub pattern to parts with a 1.5" hub pattern. The hole alternate between tapped and ...

SF-ROB-12129

This is a piezoresistive force sensor from Tekscan. The harder you press, the lower the sensor’s resistance. Pressing hard, the resistance changes ...

SF-SEN-08712

The E Style Motor mount connects to the inside of Actobotics channels and works with both standard and precision gear motors. This allows you to dr...

SF-ROB-14076

Screw plates make it easy to create a strong joining point between our channel pieces. Te small screw plate is 0.784" square, has 4 6-32 tapped hol...

SF-ROB-12128