jaycar

Linear Bearing 8mm diameter for TL4020 Specifications Diameter 8mm ...

TB-TL4034

These professional grade, high current solar charge controllers offer the flexibility to suit almost any solar installation. System voltage...

TB-MP3728

Connects Linker kit sensors/modules and Linker kit base shield. 2.54mm headers for easy and tidy connection. 4 pins, 2.54mm spaced Link...

TB-XC4560

Connects Linker kit sensors/modules and Linker kit base shield. 2.54mm headers for easy and tidy connection. 4 pins, 2.54mm spaced ...

TB-XC4558

Linker LED Module is designed for beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to to your project...

TB-XC4561

Linker LED Module is designed for beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to to your project...

TB-XC4562

Linker LED Module is designed for beginners of Arduino/pcDuino to monitor controls from digital ports. It can be mounted to to your project...

TB-XC4563

This Linker 4-digit 7-segment module uses a chipset of TM1637 to drive a 12-pin 4-digit command anode 7-segment LED. It is an ideal module ...

TB-XC4569

Connects Linker kit sensors/modules and Linker kit base shield. 2.54mm headers for easy and tidy connection. 4 pins, 2.54mm spaced Link...

TB-XC4559

This is the  base shield of Linker kit, it allows simple and tidy connection between all Linker sensors/modules and Arduino/pcDuino. Linker...

TB-XC4557

This buzzer module will generate around the audible 2kHz range. Linksprite Page   Specifications ...

TB-XC4580

Two momentary push buttons mounted on a single board for Arduino/pcDuino via the Linker connection. Can be used as a pair of reset and swit...

TB-XC4573

Flame sensor module of Linker kit is only sensitive to the light in the frequency band of infrared and ultrviolet. This breakout board ...

TB-XC4588

This hall module hosts an magnetic hall sensor that senses the presence of magnetic field. If there is an magnetic field present, it will r...

TB-XC4577

This is a high power LED module for the Linker kit. It has five very bright white LEDs to use as lamp or camera flash. Features: ...

TB-XC4570

This sharp distance sensors are a popular choice for many projects that require accurate distance measurements. This IR sensor is more econ...

TB-XC4585

The Linker Infrared Receiver Module is used to receive infrared signals and also used for remote control detection. There is an IR detector...

TB-XC4583

This LED bar is a standard Linker kit module, so it can connect to Arduino or pcDuino easily via the base shield. The LED bar has 10 light ...

TB-XC4568

The light sensor, also known as the light dependent resistor (LDR). Typically, the resistance of the light sensor will decrease when the am...

TB-XC4574

This is a magnetic switch module with Linker kit standard connection. It is based on encapsulated dry reed switch of single-pole, single th...

TB-XC4581

A standard 12mm square momentary button mounted for the Linker connection. The button is big and has a solid tactile click for assurance. Can be ...

TB-XC4571

This sensor module uses a reflective infrared sensor. The infrared light is emitted and reflected back to the receiver, it's then inverted ...

TB-XC4590

The Linker Rotary Potentiometer Module produces analog output between 0 and Vcc (5V DC with Arduino) on its D1 connector. The D2 connector ...

TB-XC4578

The Linker RTC module is based on the clock chip DS1307, which supports the I2C protocol. It utilises a Lithium cell battery (CR1225). The ...

TB-XC4584