SparkFun

Put the pedal to the metal with this metal foot switch. This is the same kind of foot pedal you might find switching the power supply for a tattoo ...

SF-COM-11192

This very long force sensitive resistor - over 2 feet - has a sensing area of 0.25x24". This FSR from Interlink Electronics will vary its resistanc...

SF-SEN-09674

This is a small force sensitive resistor. It has a 0.16" (4 mm) diameter active sensing area. This FSR from Interlink Electronics will vary its res...

SF-SEN-09673

This is a force sensitive resistor with a square, 1.75x1.5", sensing area. This FSR will vary its resistance depending on how much pressure is bein...

SF-SEN-09376

This is a force sensitive resistor with a round, 0.5" diameter, sensing area. This FSR will vary its resistance depending on how much pressure is b...

SF-SEN-09375

Amphenol FCI FFC/FPC Flexible Circuit Connectors are a broad range of innovative connector solutions to terminate FFC/FPC. This 24-Pin FPC connecto...

SF-COM-16305

FreeM is a wireless BlinkMs controller and power supply for completely standalone deployment, programming and control of BlinkM smart LEDs. It’s li...

SF-COM-10246

This is the FreeSoC2 Development Board, SparkFun’s take on the PSoC5LP ARM Cortex. The PSoC (Programmable System on a Chip) brings together feature...

SF-DEV-13229

This is the FreeSoC2 Development Board, SparkFun’s take on the PSoC5LP ARM Cortex. The PSoC (Programmable System-on-Chip) brings together feat...

SF-DEV-13714

Function generators are useful in a ton of applications from RF to embedded logic. They’re not usually super cheap though. Good news: we found a ki...

SF-KIT-11394

The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The I/O pins of this...

SF-DEV-09718

The FTDI cable is a USB to Serial (TTL level) converter which allows for a simple way to connect TTL interface devices to USB. The VCC pins of this...

SF-DEV-09717

USB C is quickly becoming more and more prominent in the maker community because, let’s be honest, who likes trying three times to insert USB into ...

SF-CAB-14909

The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads suc...

SF-COM-09479

This is a glass ferrule type fuse. It fits great with our 5mm fuse clips. The fuse is rated for 125VAC, up to 5A. Fuses are pretty simple, if more ...

SF-COM-09772

This is a glass ferrule type fuse. It fits great with our 5mm fuse clips. The fuse is rated for 250VAC, up to 500mA. Fuses are pretty simple, if mo...

SF-COM-10166

This is a 5mm PTH fuse clip intended to be used with our Glass Fuses. Note: These are sold in single units. If you intend to secure a fuse using t...

SF-COM-09773

The LIDAR-Lite v4 LED sensor is the next step in the LIDAR-Lite line. A small, lightweight, low-power optical ranging sensor. It's the first to inc...

SF-SEN-15776

This is a simple breakout board for the MQ - 3, MQ - 4, MQ - 6, MQ - 7, and MQ - 8 gas sensors. With the Gas Sensor Breakout you will be able to ut...

SF-BOB-08891

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 128 teeth with a g...

SF-ROB-12239

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 48 teeth with a ge...

SF-ROB-12232

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 64 teeth with a ge...

SF-ROB-12265

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 72 teeth with a ge...

SF-ROB-12368

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 76 teeth with a ge...

SF-ROB-12430

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 76 teeth with a ge...

SF-ROB-12256

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 84 teeth with a ge...

SF-ROB-12228

These hub-mountable aluminum gears are ideal for transmitting motion from a motor or servo to a wheel or shaft. These gears have 84 teeth with a ge...

SF-ROB-12206

These pinion gears attach to a ¼” D-shaft or gear motor using a setscrew. They have 16 teeth with a gear pitch of 32P, an outer diameter of 0.563”,...

SF-ROB-12158

These pinion gears attach to a 6mm D-shaft or gear motor using a setscrew. These gears have 16 teeth with a gear pitch of 32P, an outer diameter of...

SF-ROB-12248

These pinion gears attach to a ¼” D-shaft or gear motor using a setscrew. They have 20 teeth with a gear pitch of 32P, an outer diameter of 0.688”,...

SF-ROB-12529

These pinion gears attach to a 6mm D-shaft or gear motor using a setscrew. These gears have 20 teeth with a gear pitch of 32P, an outer diameter of...

SF-ROB-12111

These pinion gears attach to a ¼” D-shaft or gear motor using a setscrew. They have 24 teeth with a gear pitch of 32P, an outer diameter of 0.813”,...

SF-ROB-12225

These pinion gears attach to a 6mm D-shaft or gear motor using a setscrew. These gears have 24 teeth with a gear pitch of 32P, an outer diameter of...

SF-ROB-12418