Wearables

This is a simple slide switch for the LilyPad. Use it as a simple ON/OFF switch, or to control LEDs, buzzers, sensors, etc. The swtiches on each bo...

SF-DEV-09350

This is a three axis accelerometer for the LilyPad system. Based on the ADXL335 MEMS accelerometer from Analog Devices, the LilyPad Accelerometer c...

SF-DEV-09267

This is a small board for prototyping through-hole components with the LilyPad system. There are an array of pins all shorted together with 10mil t...

SF-DEV-09102

This EeonTex fabric is a bidirectionally stretchy nylon/spandex, elastic fabric coated with a long-lasting conductive formulation. This material ha...

SF-COM-14112

This EeonTex fabric is a conductive, nonwoven microfiber with piezo-resistive functionality for use in dynamic sensors to map and measure pressure,...

SF-COM-14111

This EeonTex fabric is a conductive, nonwoven microfiber for use in e-textiles as well as electromagnetic and resistive heating applications. Each ...

SF-COM-14110

The MyoWare Muscle Sensor is now designed to be wearable, allowing you to attach biomedical sensor pads directly to the board itself. However, ther...

SF-DEV-14109

This is a coin cell holder for the common CR2032 type battery. The holder has a neat pop-in, pop-out feature that makes changing the battery easy. ...

SF-DEV-08822

We designed this board to give the user a low profile button without any sharp edges. Button closes when you push it and opens when you release (mo...

SF-DEV-08776

A snap is fun, but a magnetic snap adds a whole new layer of possibilities. This are relatively large 18mm diameter snaps (all three pieces come as...

SF-DEV-08682

This is a simple pack of five Yellow LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew in...

SF-DEV-14014

This is a simple pack of five Red LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into ...

SF-DEV-14013

This is a simple pack of five Green LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew int...

SF-DEV-14011

If you’re interested in interactive toys, smart accessories, or light-up fashions, this book is for you! Sew Electric is a set of hands-on LilyPad ...

SF-BOK-12019

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure ...

SF-DEV-13903

Sure, your flashing, chip-tune playing T-shirt is really cool at the party… but at some point you need to turn it off. And yes, you could just pull...

SF-DEV-13883

This is about 360 yards of conductive thread spun from stainless steel fiber and wound on a spool. You can use it as a creative way to connect vari...

SF-DEV-11791

The SparkFun Photon Wearable Shield makes it easy to add the WiFi-enabled Photon to any wearables project. Each pin on the Photon is broken out int...

SF-DEV-13842

This battery holder features two 6″, 24-gauge leads that have 5 mm of insulation stripped off of the ends.

PL-1149

This battery holder features two 6″, 24-gauge leads that have 5 mm of insulation stripped off of the ends.

PL-1148

Discontinuation Notice: We are no longer carrying this battery holder. Please consider the 2-AAA Battery Holder as an alternative.

PL-1142

This battery holder features two 6″, 24-gauge leads that have 5 mm of insulation stripped off of the ends.

PL-1140

The MyoWare LED Shield is designed to pair with the MyoWare Muscle Sensor. The blue 10-segment bar graph shows the magnitude of the measured signal...

SF-DEV-13688

The MyoWare Power Shield is designed to take two standard CR2032 coin cell batteries to power the MyoWare Muscle Sensor. We have made this board i...

SF-DEV-13684

Would you like to learn electronics, with an all-in-one board that has sensors and LEDs built in? Circuit Playground is here - and it's the best wa...

AF-3000

This here is your standard A-miniB USB cable, for USB 1.1 or 2.0. Perfect for connecting a PC to your Teensy v2, USB Lipo charger w/Mini B connecto...

AF-260

These sew-on fabric snaps are the same size used on the LilyPad SimpleSnap boards. You can sew these into your project to allow for easy removal or...

SF-DEV-11347

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the ...

SF-COM-11289

These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the ...

SF-COM-11288

Lithium ion polymer (also known as 'lipo' or 'lipoly') batteries are thin, light and powerful. The output ranges from 4.2V when completely charged ...

AF-258

We know you love adding color to your e-textiles, adding the LilyPad Pixel Board to your project will only make it better. The pixel board is compa...

SF-DEV-13264

FLORA is Adafruit's fully-featured wearable electronics platform. It's a round, sewable, Arduino-compatible microcontroller designed to empower ama...

AF-659

This little Silver-color Pin with Foam Adhesive is the perfect way to attach any PCB or small component to cloth material. The adhesive forms a sol...

AF-2838

The LilyPad MP3 Player is your all-in-one audio solution, containing an Arduino-compatible microcontroller, MP3 (and many other formats) audio deco...

SF-DEV-11013

Bluno Beetle - The smallest Arduino Board is another milestone in wearable electronics device area based arduino uno, which makes DIY users have mo...

DF-DFR0339

This is 30 feet of conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects...

SF-DEV-10867