Wearables

The EagLED Battery Holder for CR2032 is a coin cell battery holder that holds in place a CR2032 button battery using a screw. Equipped with an ON/...

LB-EAGLED-BATTERY

EagLED is Littlebird Electronics' wearables/e-textiles development kit. It is a complete Arduino compatible microcontroller that has LEDs, Light Se...

LB-EAGLED-BUZZ

The LilyPad Light Sensor is a sewable breakout board with an ALS-PT19 light sensor built in and ready to use right away. Each sensor outputs v...

SF-DEV-14629

This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile...

SF-DEV-13814

3V - 5V 40MA E-Textiles LED Module   Paramater: Working voltage: 3V - 5V Working current: 40mA   Package included: LilyPad compatible LED Module  

LB-LR0220-B

This kit is a great way to get started with creating BBC micro:bit controlled E-Textiles projects and designs. We have selected a number of product...

KI-5607

USB-powered charger for LIR2032 coin cell batteries. DO NOT use with non-rechargeable CR2032 batteries!Note: Battery not included! Teknikio make a ...

PI-TEK012

Copper tape can be an interesting addition to your toolbox. The tape itself is made of thin pure copper so it's extremely flexible and can take on ...

AF-3483

This is the LilyPad USB Plus, a sewable electronics microcontroller board controlled by an ATmega32U4 with the Arduino bootloader. It has a built ...

SF-DEV-14631

With our fun assortment of conductive materials, cosplay and wearables have never been easier to craft! This Conductive Nylon tape goes great with ...

AF-3961

With our fun assortment of conductive materials, cosplay and wearables have never been easier to craft! This Conductive Nylon tape goes great with ...

AF-3960

A four pack of sewable, star-shaped bright blue LEDs. The voltage (and hence current) supplied from LIR2032 rechargeable coin cell batteries may da...

PI-TEK003

Two diamond-shaped, sewable LED boards that are colour-changeable! They can be connected to light up in red, blue, green, or any combination of tho...

PI-TEK005

A tiny, vibrating motor, easily attachable to paper or fabric! Just connect 3-5V across it, polarity doesn't matter, and it'll BUUUUZZZZZZ!!! The v...

PI-TEK002

The Teknikio Light Sensor Board is the easiest way to activate your sewable projects with light. It runs off their Battery Board and has two modes:...

PI-TEK006

A four pack of sewable, heart-shaped bright pink LEDs.The voltage (and hence current) supplied from LIR2032 rechargeable coin cell batteries may da...

PI-TEK004

This battery holder is by far the easiest way to add a battery to a small wearable project. There are two small 1mm diameter holes in the metal con...

PI-COM1900

A lightweight, sewable battery board that's great for paper and fabric engineering projects. Works with CR2032 coin cell batteries. The voltage (an...

PI-TEK001

This is an incredibly simple one cell 18650 Battery Holder. When someone thinks of 18650 Cells they tend to think of flashlights first, which is fa...

LB-LR0309-18

  This is a simple 6 cell AA battery holder. The 5 inch cable is terminated with a standard 5.5x2.1mm, center positive barrel jack connector.

LB-LR0294

Flat 4xAA battery holder with a 2.1mm barrel jack connecter, suited for projects including the the Arduino development board UNO.

LB-LR0309-16

Single Slots 1x 9V Battery Holder Case with wire leads for soldering / connecting.Keep your batteries organised and protectedLead Cable Length:Appr...

LB-LR0309-20

The SparkFun gator:color ProtoSnap is one of a series of gator-clippable accessories called gator:boards created to directly interface with the mic...

SF-COM-14890

The SparkFun gator:starter ProtoSnap is one of a series of gator-clippable accessories called gator:boards that have been created to directly inter...

SF-SEN-14891