Adafruit - Breakout Boards, Sensors, and Kits

This new Adafruit shield makes it easy to use a 16x2 Character LCD. We really like the RGB LCDs we stock in the shop both the RGB negative and RGB ...

AF-714

Design your own Bonnet or pHAT, attach custom circuitry and otherwise dress your Pi Zero with this jaunty prototyping Bonnet kit!To add to the Adaf...

AF-3203

Making a project that will fit into a "Altoids" Mint Tin? Put down that PCB shear and pick up a Perma-Proto in the new exciting minty shape! Cus...

AF-723

If you want to make a kit you'll need some solder. This 1/4 lb (about 110 gram) spool is just the right amount, not too much (like 1 lb spools) and...

AF-734

This 1.27mm pitch, 2x5 male SMT Box Header is the same one used on our SWD Cable Breakout Board. The header alone is great if you want to incorpora...

AF-752

With a slip ring assembly, your electronics can now twist and turn safely. Add wheel encoders, 360 degree sensors, rotating LEDs, rotors and more! ...

AF-736

The Pimoroni Speaker pHAT crams an I2S DAC and mono amplifier, a tiny 8Ω 2W speaker, and a 10 LED bar graph all onto one teeny little pHAT. It's th...

AF-3401

Finally, the conductive material you've known you wanted but never knew you could have, its a sheet of flex PCB material! This is the stuff used to...

AF-1894

Yaaar! Become your very own pirate radio station with this FM radio transmitter. This breakout board, based on the best-of-class Si4713, is an all-...

AF-1958

The NXP Precision 9DoF breakout combines two of the best motion sensors we've tested here at Adafruit: The FXOS8700 3-Axis accelerometer and magnet...

AF-3463

Make almost any surface glow, sense, or interact with Chibitronics circuit stickers! Circuit stickers are an imaginative and easy way to make fu...

AF-1974

When the future is dazzlingly-bright, this ultra-high-range luminosity sensor will help you measure it. The TSL2591 luminosity sensor is an advance...

AF-1980

Your cell phone charges off of USB, but can you really trust that charging station at the airport? Now you can control when to allow data in or out...

AF-3438

The Chip Quik No-Clean Liquid Flux Pen is great for all rework, solder, de-solder, and reflow applications! In particular this one is from the rewo...

AF-3468

A smaller-sized rechargeable battery pack for your Raspberry Pi or Raspberry Pi B+ (or Arduino, or Propeller, or anything else that works with 5V!)...

AF-1959

Is there something missing from your tool kit or workstation? Are you having trouble figuring out which elusive tool it is that you're lacking? Per...

AF-3434

Heat shrink is the duct tape of electronics which I guess makes this heat shrink the colorful and exciting duct tape they sell at craft stores.  Th...

AF-1649

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LE...

AF-3489

A button is a button, and a switch is a switch, but these translucent arcade buttons are in a class of their own. Particularly because they have LE...

AF-3491

What's a project if it's trapped on your desk? Now you can take your Arduino anywhere you wish with the PowerBoost shield! This stackable shield go...

AF-2078

Make a portable power brick with plenty of juice! Use Alkaline AA's for a 12V 3000-4000mAh power supply, or rechargeable NiMH for 2000mAh 9.6V supp...

AF-875

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices l...

AF-880

This lovely little display breakout is the best way to add a small, colorful and bright display to any project. Since the display uses 4-wire SPI t...

AF-2088

Oh say can you see By the knob's early light... Sorry - we thought that was clever.  And while it wasn't really, this potentiometer knob defini...

AF-2046