Products

Access GPIB instruments over an ethernet network using this affordable, easy to use, Prologix GPIB-ETHERNET controller. Attach the GPIB-ETHERNET co...

SF-BOB-08841

Use this unique device to download data and control GPIB bus enabled oscilloscopes, logic analyzers, function generators, power supplies, and any o...

SF-BOB-00549

This is the assembled version of the Pi T-Cobbler Plus.  It only works with the Raspberry Pi Model Zero, A+, B+, Pi 2, Pi 3 & Pi 4! (Any Pi wit...

LB-LR0387

If you want to delve into the prototyping of hardware for the Raspberry Pi, then the GPIO expansion kit is a necessity. Using a colour code...

TB-XC9042

Give your Pi some reach with this GPIO extender cable, which has two matching connectors on the end of a 12" (300mm) long gray cable. Plug one end ...

AF-1337

This 0.1mm pitch 2x2 Female Header is the perfect boost to use with boards that use the 4-pin 'PoE' header on the Raspberry Pi 3 and 4, like the Ra...

AF-4855

Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to your Pi Zer...

PI-COM1105

Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to your Pi Zer...

PI-COM1104

Absolutely no soldering required! All that's needed is a few gentle taps with a hammer and bazinga! Your header is securely attached to your Pi Zer...

PR-PIM296

If your soldering isn't quite up to scratch, or you just don't own a soldering iron yet, then these nifty hammer headers from Pimoroni might be jus...

AF-3413

Connect your own PCB to a Raspberry Pi with this extra-tall female header. The female header part has extra spaces to make it 13.6mm tall: when pla...

AF-1658

Connect your own PCB to a Raspberry Pi B+ with this normal-height female header.  The female header part is about 8.5mm tall, good for small HATs t...

AF-2222

This 'shorty' 2x20 header is great for a slim connection to your Raspberry Pi model A+ or B+, it's basically the  through-hole version of the SMT G...

AF-2243

Connect your own PCB to a Raspberry Pi 3 with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: when p...

PI-COM0004

Connect your own PCB to a Raspberry Pi B+ with this extra-tall female header. The female header part has extra spaces to make it 16.5mm tall: when ...

AF-1992

The GPIO extension kit used for extending the GPIO interface on Raspberry Pi B+, it helps you break out all those tasty power, GPIO, I2C and SPI pi...

EC-RA000022RK

Connect this to that! If you want to bridge those contacts out onto another PCB, you'll want this GPIO Ribbon Cable! Comes in a classic Adafruit Bl...

AF-4170

That new Raspberry Pi® Model A or B computer you just got has a row of 2x13 pin headers soldered on - those are the GPIO (general purpose input/out...

AF-862

That new Raspberry Pi® Model B+ computer you just got has a row of 2x20 pin headers soldered on - those are the GPIO (general purpose input/output)...

AF-1988

Connect your own PCB to a Raspberry Pi B+ and stack on top with this normal-height female header with extra long pins.  The female header part is a...

AF-2223

INTRODUCTION The Raspberry Pi GPIO Triple Expansion Board converts the single GPIO headers on your Raspberry Pi into thr...

DF-DFR0385

Extra-long and bendy, this is just like your classic Model A or B Pi GPIO cable but 12" (300mm) long and fitted through a tube so that it's a littl...

AF-1338

This product was replaced by a updated version GPRS Shield V2.0 (SLD01098P).   GPRS Shield V2   The GPRS (General Packet Radio Service) ...

SS-103030013

This product was replaced by an updated version GPRS Shield V3.0   Hook your Arduino up to GSM/GPRS cell phone network with GPRS shield! You can ...

SS-113030000

The difference between this version and the previous version is, changing the arduino socket to the latest Arduino Uno standard. Except this, all ...

SS-113030009

The A9G development board is a multifunctional development board based on EMC’s A9G GPRS/ GSM + GPS/ BDS module, you can use it to verify the basic...

EC-AMC01017B

The GPRSbee is a GPRS/GSM expansion board, designed by Gregory Knauff   The board has the bee form factor and can be used in any system that has ...

SS-113990065

The GPRSbee SMA is a GPRS/GSM expansion board, designed by Gregory Knauff. It is almost identical with the original GPRSbee, but in addition to th...

SS-113990054

The GPRSbee U.FL is a GPRS/GSM expansion board, designed by Gregory Knauff. It is almost identical with the original GPRSbee, but instead of the S...

SS-113990053

Overview This is a GPS Active Antenna. Its cable is 3m. Features  Frequency: 1575.42MHZ Voltage: 3.0-5.0V Size: 3.9 x 5.0cm Cable Length: 3m(Appro...

IT-IM120717003

This is a GPS Active Antenna which can make you received the GPS form indoor. Its cable is 3m. It can be used with our GPS Shield to make the GPS S...

EC-WAG03010G

Give your Ultimate GPS V3 a boost with this external active antenna. This GPS antenna draws about 10mA and will give you an additional 28 dB of gai...

AF-960

Want to improve your GPS antenna multipath convergence time performance to near survey-grade GNSS levels? Just using this simple steel plate effect...

SF-GPS-15004

Many magnetic mount GPS antennas rely on being mounted on a car or other large metallic object to provide a good ground plane. But what if you want...

SF-GPS-17519

GPS Bee, a SKM58 breakout that adds a Xbee compatible footprint for SKM58. The SKM58 Series with embedded GPS antenna enables high perf...

TB-XC4600

As somebody worry about the price of Seeeduino Stalker will be too high with GPS module , so we separate the GPS module away from stalker . And to...

SS-113050003

Ublox makes some incredibly sophisticated GPS receivers like the NEO-M8P. The SAM-M8Q is just as high quality, with equally impressive configurabil...

SF-SPX-15106

The GPS Expansion for the Onion Omega is a USB-based expansion that allows your Omega to pinpoint its location using both GPS as well as China’s Be...

ON-GPSEXP

Measure location, altitude, and speed using your Arduino and this module. Simple serial interface with full Arduino library support. Onboard backup...

FT-GPS

DISCONTINUED: This product has been discontinued, the page is available for reference and documentation.   GPS module for Gadgeteer.  This module ...

SS-109120000

Copernicus II is the latest iteration of the popular Copernicus GPS module from Trimble. The Trimble Copernicus II delivers proven performance and ...

SF-GPS-10922

Venus638FLPx is a high performance, low cost, single chip GPS module targeting mobile consumer and cellular handset applications. It offers very lo...

SF-GPS-10919

You must have used a GPS receiver. It is easy to be found in most places, such as smartphones, cars, and computers. They are used to track your ...

DF-TEL0094