Pololu Australia

0.25″-diameter short-tail force sensing resistor (FSR) next to a 0.2″-diameter FSR with a standard tail. Overview This force-sensing resist...

PL-1695

Overview These side-entry terminal blocks have terminals that hold and release wires through the simple adjustment of a small screw, allowing you ...

PL-2499

Overview These cylindrical brushed DC gearmotors are available in a wide range of gear ratios and with five different motors (two power levels of ...

PL-1591

Overview These side-entry terminal blocks have terminals that hold and release wires through the simple adjustment of a small screw, allowing you ...

PL-2493

Overview The Pololu basic relay carrier modules make it easy to control a single-pole, double-throw (SPDT) switch from low-voltage, low-current...

PL-2482

These 0.1 μF 50 V ceramic capacitors have many uses, including noise suppression on motors. The leads are formed with 0.1″ spacing for easy bread...

PL-2451

Overview These terminal blocks have terminals that hold and release wires through the simple adjustment of a screw, allowing you to easily make te...

PL-2444

Overview These terminal blocks have terminals that hold and release wires through the simple adjustment of a screw, allowing you to easily make te...

PL-2441

Pololu 40×7mm wheels. Motor Connections These wheels are designed to press-fit securely onto the 3mm D output shafts on many of our gearmotors...

PL-1452

60×8mm wheel with tire removed. Description These wheels are designed to press-fit securely onto the 3mm D output shafts on many of our gear...

PL-1420

This heavy duty single-pole, double-throw (SPDT) toggle switch makes a great power switch or state selector for user interfaces. It is rated for ...

PL-1407

This single-pole, double-throw (SPDT) momentary switch can be used as a general-purpose micro switch or tactile obstacle-detector for your robot. ...

PL-1402

Mini 2-pin, PCB-mount pushbutton switch on a breadboard. Overview These small, two-pin, SPST momentary pushbuttons are intended for mounting...

PL-1400

Getting started with the Maestro Servo Controller For a full list of products shown in this video, see the blog post. Overview Maestro family o...

PL-1352

This lightweight (about 7.5 g) but strong bracket is made from 2mm-thick black anodized aluminum and is specifically designed to work with the...

PL-2257

Arduino Leonardo, top view. Arduino Leonardo, bottom view. Note: There are differences between the Leonardo and previous Arduino boards. As...

PL-2192

Overview The AR-3606HB is a standard-sized servo that has been built by Power HD specifically for continuous rotation. At 6 V, it has a maximum ro...

PL-2149

This battery holder features two 6″, 24-gauge leads that have 5 mm of insulation stripped off of the ends.

PL-1141

This is a great general-purpose actuator for tiny mechanisms. The lead is terminated with a standard “JR”-style connector, which is Futaba-compat...

PL-2145

Overview A4990 dual motor driver carrier, bottom view with dimensions. Allegro’s A4990 is a dual H-bridge motor driver IC that can be used f...

PL-2137

This is the 130-size DC motor used in the larger Pololu plastic gearmotors (228:1 offset, 120:1 offset, 200:1 90-degree, and 120:1 90-degree). It...

PL-1117

This 5.5" (14cm) cable has two 26AWG conductors with a 2mm-pitch 2-pin female JST PH-style connector. The other ends of the wires are unterminated...

PL-1116

Overview These boost (step-up) voltage regulators generate higher output voltages from input voltages as low as 2.5 V. They are switching reg...

PL-2116

0.1" connector custom cable. These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connect...

PL-3339

PL-1077

PL-1076

0.1" connector custom cable. These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connect...

PL-3334

0.1" connector custom cable. These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connect...

PL-3330

PL-1069

USB A to Micro-B cable size comparison: standard cable (#2073) on left, thin cable (#2072) on right. This USB cable is six feet long (1.8 m)...

PL-2073

Overview These 0.1" straight female header strips are commonly used as low-cost connectors for custom-made cables or perforated prototyping PCBs. ...

PL-1013

Overview These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-...

PL-997

Overview These tiny brushed DC gearmotors are available in a wide range of gear ratios—from 5:1 up to 1000:1—and with five different motors: high-...

PL-993

This cable is well suited to serve as an AVR ISP programming cable and is included with our Orangutan USB Programmer, or it can simply serve as a ...

PL-972

Pololu ball caster with 1/2" plastic ball with included hardware. Overview This ball caster kit includes a black ABS housing, a 1/2″ diamete...

PL-952

These universal mounting hubs are designed to work with most 6 mm diameter shafts, including round shafts and “D” shafts. Each of the two include...

PL-1999

Pololu ball caster with 3/8" plastic ball with included hardware. Overview This ball caster kit includes a black ABS housing, a 3/8″ diamete...

PL-950

PL-1960

PL-1957

Overview The Zumo 32U4 is a highly integrated, user-programmable and customizable tracked robot. It measures less than 10 cm on each side and weig...

PL-3126

Overview These M-F (male-female) aluminum standoffs are great for separating stacked components or chassis tiers. Each hexagonal standoff is ...

PL-1940

Note: This crimping tool is 3 mm narrower than our more versatile 0.1-1.0 mm² capacity crimper, and it does not crimp the full extent ...

PL-1929

This Futaba J connector has a 0.1" pin spacing and mates with the female connectors found on many Futaba servos. It is keyed to enforce proper cab...

PL-1927

Overview A-Star 32U4 Prime SV, bottom view. The Pololu A-Star 32U4 Prime is a general-purpose programmable board based on the ATmega32U4 AVR...

PL-3115

This JR connector has a 0.1" pin spacing and is commonly used on RC servos. Two corners are slightly beveled, which makes it difficult (but not i...

PL-1924

Overview These housings work with our wires with pre-crimped terminals and our crimp pins to let you quickly make custom cables that mate with var...

PL-1916

Pre-cut and pre-stripped wires simplify and speed up breadboarding work. Having exactly the right wire lengths for the job also makes your project...

PL-312

0.1" connector custom cable. These wires with pre-crimped terminals are equivalent to our premium jumper wires without the 1×1 crimp connect...

PL-1804